background image

13

INT-150 Owners Manual

Please check with the factory-authorized distributor in the country you are 
purchasing this product for specific warranty information.

All Pass Laboratories products purchased from an authorized Pass Labora-
tories dealer in North America are covered by a transferable, limited 3-year 
warranty.  This warrantee includes all parts and labor charges incurred at the 
repair facility in addition to return shipping to the domestic customer, exclu-
sive of  subsequent damages.  Damage due to physical abuse is specifically 
not covered under this warranty.

For  this  warranty  to  apply  the  customer  is  responsible  for  returning  the 
product unmodified to the factory within the warranty period. The customer 
assumes all responsibility for shipping and insurance to the factory or a fac-
tory specified repair facility.  The conditions and stipulations of  this Pass 
Laboratories warranty only applies to units sold new in North America.

Non-North America customers should consult with their original Pass Labs 
dealer or distributor for warrantee repair instruction prior to contacting the 
factory or shipping product for repair.  

Non-North American product must be returned to the country of  origin for 
warrantee service.  Foreign distributors are only required to offer warranty 
service on Pass Laboratories product that they have imported.  

Please note: Conditions of  warranty service and customer rights for product 
purchased outside the United States may vary depending upon the distribu-
tor and local laws.  Please check with your local distributor for specific rights 
and details.

Any  modifications  to  Pass  Laboratories  products  that  have  not  received 
written factory approval nullify all claims and void the warrantee.  Should a 
modified product be returned to the factory for repair the owner will be re-
quired to pay all necessary charges for the repair in addition to those charges 
required to return the product to it’s original configuration.

In the case of  safety issues, no product shall be returned to the customer 
without  those  safety  issues  being  corrected  to  the  most  recent  accepted 
standards.

Removal or alteration of  original Pass Labs serial numbers voids the factory 
warranty.  Product with altered or missing serial numbers will be suspected 
as counterfeit product.

Pass Laboratories will not repair or in any way indemnify any counterfeit or 
cloned product.

Pass  Laboratories  does  not  offer  products  in  voltages  intended  for  inter-
national markets either to authorized Pass Labs dealers or to third parties 
located in the United States or Canada.

Warranty Information

Pass Laboratories, PO Box 219, Foresthill, CA  95631  USA, 

 530.367.3690

Содержание INT-150














Отзывы: