background image

www.parweld.com

6

6) Main amperage control.

 This control is used to control the 

welding current in TIG and MMA modes. Please not the maximum 

output of this machine varies depending upon the input voltage and 

the process selected, refer to the technical data.

7) Downslope/arc force.

 This control is dual function

in TIG mode it controls the downslope time for the welding current 

after the trigger is released from 0 to 10 seconds.
In MMA mode it allows adjustment of the welding Arc force so giving 

control of penetration.

8) posative connection

 This is used to connect the electrode holder 

in MMA or the earth lead in TIG welding.

9) Negative connection.

 This is used to connect the earth lead in 

MMA welding or the torch in TIG welding.

10) Control socket 

This is used to control the machine remotely 

using a trigger or amperage control

11) Gas Output connection

 

This is a 3/8 BSP connection for the gas output used 

in TIG welding.

12) 

This is a nipple connection for the gas input used in TIG welding.

 

5.0 Installation

Read entire installation section before starting installation.

SaFetY preCautIOnS

• ELECTRIC SHOCK can kill.
• Only qualified personnel should perform this installation.
• Only personnel that have read and understood the Operating 

Manual should install and operate this equipment.
• Machine must be grounded per any national, local or other 

applicable electrical regulations.
• The power switch is to be in the OFF position when installing 

work cable and electrode cable and when connecting other 

equipment.

5.1 Unpacking the Machine

Carefully remove the machine from the packaging, we recommend  

you retain the packaging until the machine has been fully installed 

and tested incase it has been damaged in transit and has to be 

returned to the re-seller.

5.2 location

Be sure to locate the welder according to the following guidelines:
In areas, free from moisture and dust. 
Ambient temperature between 0-40

0

C.

In areas, free from oil, steam and corrosive gases.
In areas, not subjected to abnormal vibration or shock.
In areas not exposed to direct sunlight or rain.
Place at a distance of 12” (300 mm) or more from walls or similar 

that could restrict natural airflow for cooling.

5.3 Input and grounding connection 

WarnInG

Before starting the installation, check that your power supply 

is adequate for the voltage, amperage, phase, and frequency 

specified on the Machine nameplate.

Operate the welding power source from a single-phase 50/60 Hz, 

AC power supply. The input voltage must match one of the electrical 

4.0 Description of Controls

1) On OFF Switch

 for switching on or off the mains supply to the 

machine. Note the output of the machine is permanently on in MMA 

mode unless the on/off switch is in the off position.

2) Fault light

 This indicates a fault or over temperature condition 

with the machine refer to the fault finding section for further 

information 

3) Power light

 This indicates mains power is applied to the machine 

and that the machine is currently switched on when the light is 

illuminated.

4) process selector

. This switch has 3 positions the bottom 

position selects MMa welding and will latch on the output when in 

this position. The centre position is TIG welding with 2 touch trigger 

control (momentary). The top position is TIG welding with 4 touch 

control (latching).

5) tIG mode

, this toggles between LIFT-ARC mode and HF start 

TIG. 

1

2

4

5

7

8

10

12

3

6

11

9

CO

ntr

O

lS

Содержание XTT-182 DV



















Отзывы: