background image

GB

14

1740281

TROUBLE SHOOTING CHART

TROUBLE

CAUSE

CORRECTION

Difficult starting

Defective spark plug.

Replace spark plug.

Water or dirt in fuel system.

Use carburetor bowl drain to flush and refill with

fresh fuel.

Engine runs erratic

Blocked fuel line, empty gas tank, or stale petrol

Clean fuel line; check fuel supply; add fresh

petrol

Engine stalls

Unit running on CHOKE.

Set choke lever to RUN position.

Engine runs erratic;

Loss of power

Water or dirt in fuel system.

Use carburetor bowl drain to flush and refill with

fresh fuel.

Excessive vibration

Loose parts: damaged impeller

Stop engine immediately and disconnect spark

plug wire. Tighten all bolts and make all

necessary repairs. If vibration continues, have

the unit serviced by a competent repairman.

Unit fails to propel itself

Drive belt loose or damaged.

Replace drive belt.

Unit fails to discharge snow

Auger drive belt loose or damaged.

Adjust auger drive belt; replace if damaged.

Auger control cable not adjusted correctly.

Adjust auger control cable.

Discharge chute clogged.

Stop engine immediately and disconnect spark

plug wire. Clean discharge chute and inside of

auger housing.

Foreign object lodged in auger

Stop engine immediately and disconnect spark

plug wire. Remove object from auger.

Содержание 621504x117NA





















Отзывы: