background image

 

All-in-one solar charge inverter    V11                                                                                                                                                               25 

4.2  Setup parameters description 

Buttons operation instructions: Press the “SET” button to enter the setup menu and exit the setup 

menu. After entering the setup menu, the parameter number [00] will flash. At this point, press the “UP” 
and “DOWN” buttons to select the code of parameter item to be set. Then, press the “ENT” button 
to enter the parameter editing mode, and the value of the parameter is flashing. Adjust the value of the 
parameter with the “UP” and “DOWN” buttons. Finally, press the “ENT” button to complete the 
parameter editing and return to the parameter selection state. 

 

Parameter 

no. 

Parameter 

name 

Settings 

Description 

00 

Exit setting 

menu 

[00] ESC 

Exit the setup menu 

01 

Output source 

priority 

[01] SOL 

PV priority mode, switching to the Mains when the PV 
fails or the battery is lower than the set value of 
parameter [04]. 

[01] UTI 

default

 

Mains priority mode, switching to inverter only when 
the mains fails. 

[01] SBU  

Inverter priority mode, switching to the mains only 
when the battery is under voltage or lower than the 
set value of parameter [04]. 

02 

Output 

Frequency 

[02] 50.0

 

 

Bypass self-adaptation; when the mains is connected, 
it automatically adapts to the mains frequency; when 
the mains is disconnected, the output frequency can 
be set through this menu. The default output 
frequency of the 230V machine is 50HZ。 

[02] 60.0 

03 

AC Input 

Voltage Range 

[03] APL  

Wide mains input voltage range of 230V machine: 
90~280V 

[03] UPS 

default

 

Narrow mains input voltage range of 230V machine: 
170~280V 

04 

Battery Power 

to Utility 
Setpoint 

[04] 43.6 

default

 

When the parameter [01] =SOL/SBU, the battery 
voltage is lower than the set value, and the output is 
switched from the inverter to the mains. Setting 
range: 44V~52V. Cannot exceed the value of [14] 
settings. 

05 

Utility to 

Battery Power 

Setpoint 

[05]57.6V 

default

 

When the parameter [01] =SOL/SBU, the battery 
voltage is higher than the set value, and the output is 
switched from the mains to the inverter. Setting 
range: 48V~60V.

  

Cannot be lower than the value of  

[04] / [35]  settings. 

Содержание HF4830S60-145








































Отзывы: