the required cutting depth. Then re-tighten
the knurled nut on the screw (27).
Check the adjustment by making a test cut.
8.6 Sawdust bag (Fig. 2)
The saw is equipped with a debris bag (22) for
sawdust and chips.
The debris bag (22) can be emptied by means
of a zipper at the bottom.
8.7 Changing the saw blade (Fig. 1, 17 – 20)
Remove the power plug!
Swing up the machine head (5). Use the
safety pin (25) to lock the machine head in
this position.
Press the release lever (3) and swing up the
saw blade guard (6) to the point where the
recess in the saw blade guard (6) is above
the flange bolt (31).
Press the saw shaft lock (4) with one hand.
With the other hand position the wrench (c)
over the flange bolt (31).
Firmly press the saw shaft lock (4) and
slowly rotate the flange bolt (31) in
clockwise direction. The saw shaft lock (4)
engages after no more than one rotation.
Now, using a little more force, slacken the
flange bolt (31) in the clockwise direction.
Turn the flange screw (31) right out and
remove the external flange (32).
Take the saw blade (7) off the inner flange
(38) and pull it out downwards.
Carefully clean the flange bolt (31), outer
flange (32) and inner flange (38).
Fit and fasten the new saw blade (7) in
reverse order.
Important.
The cutting angle of the teeth, in
other words the direction of rotation of the
saw blade (7) must coincide with the
direction of the arrow on the housing.
Before continuing your work make sure that
all safety devices are in good working
condition.
Important.
Every time that you change the
saw blade (7), check to see that it spins
freely in the table insert (11) in both
perpendicular and 45° angle settings.
Important.
The saw blade (7) must be
changed and aligned correctly.
8.8 Transport (Fig. 1 – 3)
Tighten the locking grip (13) to lock the
turntable (16).
Press the release lever (3), push the
machine head (5) to the rear and lock it with
the locking bolt (25). The saw is now locked
in its lower position.
Secure the drag function of the saw in its
rear position using the fixing screw for the
drag guide (24).
Carry the equipment by the fixed saw table
(17).
When reassembling the equipment proceed
as described under section 7.2.
8.9 Using the laser (Fig. 21-23/Item. 33)
To switch on:
Move the ON/OFF switch of
the laser (34) to the “1” position. A laser
line is projected onto the material you wish
to process, providing an exact guide for the
cut.
To switch off:
Move the ON/OFF switch of
the laser (34) to the “0” position.
Setting the laser:
Slacken the screws (37)
to adjust the laser. Retighten the screws
after you have made the adjustment.
Important. Never look directly into the laser
beam!
Replacing the battery:
Switch off the laser
(33). Remove the battery compartment
cover (36). Remove the batteries and
replace with new batteries (2 x 1.5 Volt
Type R03, LR 03 Micro, AAA) Check that
the battery terminals are positioned
correctly when inserting new batteries.
Close the battery compartment (35) again.
9. Replacing the power cable
If the power cable for this equipment is
damaged, it must be replaced by the
manufacturer or its after-sales service or
similarly trained personnel to avoid danger.
GB/IE/
CY
19
Anleitung_4300696:_ 10.07.2009 12:31 Uhr Seite 19
Содержание ZKGS 2100 UG
