4.1 Items supplied with the base frame
(Figs. 24, 25)
39. 4 x supporting foot, upper part
40. 4 x supporting foot, lower part
a. 2 x upper cross strut, short
b. 2 x upper cross strut, long
A. 2 x lower cross strut, long
B. 2 x lower cross strut, short
41. 4 x M6 x 40mm screw
42. 32 x M6 x 12 mm screw
43. 40 x M6 washer
44. 36 x M6 spring washer
45. 36 x M6 nut
46. 4 x rubber stop for supporting foot
5. Proper use
The drag, circular crosscut and miter saw is
designed to crosscut wood and plastic suitable
for the machine’s size. The saw is not designed
for cutting firewood.
The machine is to be used only for its
prescribed purpose. Any other use is deemed
to be a case of misuse. The user / operator
and not the manufacturer will be liable for any
damage or injuries of any kind caused as a
result of this.
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be
voided if the machine is used in commercial,
trade or industrial businesses or for equivalent
purposes.
The machine is to be operated only with
suitable saw blades. It is prohibited to use any
type of cutting-off wheel.
To use the machine properly you must also
observe the safety regulations, the assembly
instructions and the operating instructions to
be found in this manual.
All persons who use and service the machine
have to be acquainted with this manual and
must be informed about its potential hazards.
It is also imperative to observe the accident
prevention regulations in force in your area.
The same applies for the general rules of
occupational health and safety.
The manufacturer shall not be liable for any
changes made to the machine nor for any
damage resulting from such changes.
Even when the machine is used as prescribed
it is still impossible to eliminate certain residual
risk factors. The following hazards may arise in
connection with the machine’s construction
and design:
Contact with the saw blade in the
uncovered saw zone.
Reaching into the running saw blade (cut
injuries).
Kick-back of workpieces and parts of
workpieces.
Saw blade fracturing.
Catapulting of faulty carbide tips from the
saw blade.
Damage to hearing if essential ear-muffs
are not worn.
Harmful emissions of wood dust when the
machine is used in closed rooms.
The product complies with the
requirements of the EN 61000-3-11 and is
subject to special connection conditions.
This means use at freely chosen normal
connection points is prohibited.
The appliance can lead to temporary
fluctuations in voltage if the mains supply is
unreliable.
The product is only to be used at sockets
which have a resilient steady mains current
of at least 100 A per phase.
As the operator, you must ensure that your
socket satisfies the specified
requirements.(If necessary, confer with
your energy supplier)
GB/IE/
CY
15
Anleitung_4300696:_ 10.07.2009 12:31 Uhr Seite 15
Содержание ZKGS 2100 UG
