Parkside PKS 1500 B3, Руководство по эксплуатации и технике безопасности

Страница: 15 / 100

10 GB/IE/NI
9.5 Precision adjustment of the stop for mitre cut at
45° (fig. 1/2/3/6/7/8)
No stop angle included.
• Lower the machine head (4) and secure it using the locking
bolt (25).
• Fix the rotary table (13) in the 0° position.
• Important. For mitre cuts, the adjustable stop rail (8a) must
be fixed at the inner position.
• Open the set screw (8b) for the adjustable stop rail (8a) and
push the adjustable stop rail (8a) outwards.
• The adjustable stop rail (8a) must be fixed far enough in
front of the innermost position that the distance between the
adjustable stop rail (8a) and the saw blade (6) amounts to
a maximum of 8 mm.
• Before making a cut, check that the adjustable stop rail (8a)
and the saw blade (6) cannot collide.
• Secure the set screw (8b) again.
• Loosen the locking screw (23) and use the handle (3) to
angle the machine head (4) 45° to the left.
• 45° - position angle stop (B) between the saw blade (6) and
rotary table (13).
• Loosen the locknut (22a) and adjust the adjusting screw (22)
until the angle between the saw blade (6) and the rotary
table (13) is precisely 45°.
• Re-tighten the locknut (22a).
• Subsequently check the position of the angle indicator. If
necessary, loosen the pointer (28) using a Philips screwdriv-
er, set to position 45° on the angle scale (27) and re-tighten
the retaining screw.
9.6 Mitre cut between 0°and 45° and rotary table
at 0°(fig. 1/2/3/6)
The cross cut mitre saw can be used to make mitre cuts between
0° and 45° in relation to the work face.
Important!
For mitre cuts, the adjustable stop rail (8a) must be
fixed at the inner position.
Attention!
For mitre cuts between 0° and 45°, mount the
clamping device (workpiece clamp) (15) only on
the right side.
• Open the set screw (8b) for the adjustable stop rail (8a) and
push the adjustable stop rail (8a) outwards.
• The adjustable stop rail (8a) must be fixed far enough in
front of the innermost position that the distance between the
adjustable stop rail (8a) and the saw blade (6) amounts to
a maximum of 8 mm.
• Before making a cut, check that the adjustable stop rail (8a)
and the saw blade (6) cannot collide.
• Secure the set screw (8b) again.
• Move the machine head (4) to the top position.
• Fix the rotary table (13) in the 0° position.
• Loosen the locking screw (23) and use the handle (3) to
angle the machine head (4) to the left, until the pointer (28)
indicates the desired angle measurement on the scale (27).
• Re-tighten the locking screw (23).
• Cut as described in section 9.3.
9.7 Mitre cut between 0° and 45° and rotary
table between 0° and 45° (fig. 1/2/3/6)
The cross cut mitre saw can be used to make mitre cuts to the
left of 0°- 45° in relation to the work face and, at the same
time, 0° - 45° to the left or 0° - 45° to the right in relation to
the stop rail (double mitre cut).
Attention!
For mitre cuts (inclined saw head), the adjustable
stop rail (8a) must be fixed in the outer position.
Attention!
For mitre cuts between 0° and 45°, mount the
clamping device (workpiece clamp) (15) only on
the right side.
• Open the set screw (8b) for the adjustable stop rail (8a) and
push the adjustable stop rail (8a) outwards.
• The adjustable stop rail (8a) must be fixed far enough in
front of the innermost position that the distance between the
adjustable stop rail (8a) and the saw blade (6) amounts to
a maximum of 8 mm.
• Before making a cut, check that the adjustable stop rail (8a)
and the saw blade (6) cannot collide.
• Secure the set screw (8b) again.
• Move the machine head (4) to its upper position.
• Release the rotary table (13) by loosening the set screw (7).
• Using the handle (3), set the rotary table (13) to the desired
angle.
• Retighten the set screw (7) in order to secure the rotary table.
• Undo the locking screw (23).
• Use the handle (3) to tilt the machine head (4) to the left until
it coincides with the required angle value (in this connection
see also section 9.6).
• Re-tighten the locking screw (23).
• Cut as described under section 9.3.
9.8 Changing the saw blade (fig. 1/2/3/9/10)
Remove the power plug!
Important!
Wear safety gloves when changing the saw blade.
Risk of injury!
• Swing the machine head (4) upwards and secure with the
locking bolt (25).
• Fold the saw blade guard (5) upwards until the saw blade
guard (5) is above the flange screw (29).
• With one hand insert the Allen key (C) in the flange screw
(29).
• Hold the Allen key (C) and slowly close the saw blade guard
(5) until it touches the Allen key (C).
• Firmly press the saw shaft lock (32) and slowly rotate the
flange screw (29) in clockwise direction. The saw shaft lock
(32) engages after no more than one rotation.
• Now, using a little more force, slacken the flange screw (29)
in the clockwise direction.
• Turn the flange screw (29) right out and remove the outer
flange (30).
• Take the blade (6) off the inner flange and pull out down-
wards.
• Carefully clean the flange screw (29), outer flange (30) and
inner flange.
• Fit and fasten the new saw blade (6) in reverse order.