background image

Bolt down the crosscut and mitre saw on to a steady surface using the holding down bolt holes 

provided in the base.

Support long workpieces on a surface or blocks so that it is at the same height as the saw table. This will  stop long workpieces 
from tipping over.

Always keep the power cable well out of the saw's working area and fed to the rear of the machine.   

Look after your health: Wear ear defenders - also wear safety glasses and a breathing /dust mask.

After you have used the machine secure it with the locking button 

.

Only use saw blades that have a diameter of 250 mm and are suitable for the type of clamping flange on the saw. Saw blades with hardened 
metal teeth must have a negative rake angle.

Do not use saw blades that have deep hook teeth.

Do not use saw blades that have a recommended speed of less than 3800 revolutions per minute.

The head bolt on the spindle and retainer must always be kept clean.

Always check the workpiece carefully for any foreign bodies (nails etc.) and remove all dangerous items from area of the saw cut.

Never reach behind the blade. Only remove any material accumulated there once the saw has been unplugged and the blade has stopped rotating.

Do not cut too small a workpiece. Your hand must always remain at least 10 cm away from the saw blade. 

Use G clamps (c) or other mountings to ensure that any (e.g. awkwardly shaped) workpiece cannot slide or rotate during cutting. The 
workpiece must be held tightly against the saw table base and stop plate so that there are no gaps between the workpiece and the saw table 
or the stop plate. 

Make sure that all the clamps and stops are always tightly seated. 

Never cut more than one workpiece at a time. 

Make sure that the saw blade has reached its full speed before any cut is started and do not use too much force. This should avoid the saw 
being brought to a standstill.

ASSEMBLY

Only connect your crosscut and mitre saw to the power supply when you have followed all these instructions and completely assembled 
the saw.
Pick up the saw using the transverse support stirrup 

or the base plate and remove it from the packaging. Do not lift or carry the saw 

by the actuating handle 

as this can lead to misalignment.

1. Insert the transverse support stirrups 

into the openings provided in the left and right hand sides of the base.

2. Fully screw the stop setting handle 

for setting the stops on the saw table tightly into the threaded hole provided.

3. Unscrew the stop setting handle 

 

again two or three turns and rotate the saw table 

 

using the control lever 

(pressing the 

control lever disengages the stop and allows the saw table to be turned to the left or right into the desired position) into the home position 
(0° - setting). 

4. When the control lever 

is engaged in the home position, retighten the stop setting handle 

to set the stop for the saw.

5. Press the actuating handle 

down gently and pull out the locking button 

. The cutting head can be moved into the open upper position.

6. Attach the dust extraction bag (b) to the dust extraction outlet 

. See that the dust bag sealing ring fits into the groove in the dust 

extraction outlet.

7. So that you can work safely we recommend that you fasten down the crosscut and mitre saw on to a flat surface using the threaded holes 

provided in the underside of the saw base.

!

5

Содержание PKGS 1400 CROSSCUT MITRE SAW











Отзывы: