PDR 12 A1
GB│IE
│
13
■
CAUTION!
►
Never fill the water tank with solvents, liquids
containing solvents, or undiluted acids (e .g .
cleaning agents, petrol, paint thinner, acetone) .
They could damage the materials used in the
appliance .
►
Do not leave the appliance unattended while
it is in operation .
►
Do not leave the appliance unattended while
it is connected to the power supply .
►
Place the appliance on a firm, level surface to
ensure stability .
CAUTION!
►
Do not operate the appliance at temperatures
below 0°C .
Safety equipment
CAUTION
►
Do not change or bypass the safety functions of
the appliance . They are there for your safety .
The safety equipment is designed to protect the user and may not be
deactivated or repurposed .
Pressure switch
The pressure switch activates the low-pressure spray jet . When you let go
of the trigger, the low-pressure spray jet stops .
Appliance switch
The appliance switch prevents the appliance from being switched on
unintentionally .
Motor protection circuit breaker
The appliance switches off automatically when the power consumption
becomes too high .
Before use
Operating the appliance on a 12 V circuit
WARNING!
►
The current tolerance of your vehicle's wiring system must be
compatible with the connected appliance .
►
Refer to your vehicle handbook (cigarette lighter) .
♦
Remove the charging socket cover .
♦
Connect the correct end of the 12 V cable to the 12 V socket
on the appliance .
♦
Connect the 12 V connector plug
10a
with a suitable socket . This is
usually the cigarette lighter socket on the dashboard of your vehicle .
Many vehicles have a second socket by the rear seats or in the boot .
The red LED on the 12 V connector plug
10a
lights up .
♦
You can now run the appliance on the 12 V socket . Please note that
this does not charge the battery .
♦
Disconnect the 12 V connector plug
10a
from the cigarette lighter socket
when you are finished using the appliance .
♦
Remove the 12 V cable from the 12 V socket .
♦
Close the 12 V socket
again by replacing the charging socket
cover .
Charging the appliance with the mains adapter
NOTE
►
While the battery is charging, the status LED lights up red .
►
When the battery is fully charged, the status LED lights up green .
►
It takes approximately 1 hour for the battery to charge fully when
empty .
♦
Remove the charging socket cover .
♦
Connect the end of the charger cable to the charging socket on the
mains adapter
5a
.
♦
Plug the mains adapter into a mains power outlet .
♦
Disconnect the mains adapter from the mains power outlet and the
charging socket of the mains adapter
5a
as soon as the battery is fully
charged .
♦
Replace the charging socket cover to close the charging socket .
Filling the water tank
♦
Turn the water tank towards the Open mark until you can pull the
water tank
off the base . Hold the base firmly with one hand to
create suitable counter-pressure .
♦
Open the lid of the water tank . Use a tap to fill the water tank
with water . Do not fill the tank beyond the 5 l mark .
NOTE
►
The water tank has a capacity of 5 litres .
►
Fill the water tank with fresh water only .
►
Do not open the lid during operation .
♦
Close the lid of the water tank .
♦
Put the water tank
back on the base . Turn the water tank
towards the Close mark on the base until it clicks into place .
Hold the base firmly with one hand to create suitable counter-pressure .
Ensure that the
I
mark on the base is aligned with the
I
mark on the
water tank
when it has clicked into place .
Operation
Switching the appliance on
CAUTION!
►
If the pump runs for 2 minutes without drawing in liquid, it will run dry
and the appliance will be damaged .
♦
Press the On/Off switch to switch the appliance on . The status
LED lights up green . The pump builds up pressure .
Turning the appliance off
♦
Press the On/Off switch again to switch the appliance off .
The status LED goes out .
Содержание PDR 12 A1
Страница 3: ...A 5a 10a...
