manualshive.com logo in svg
background image

INTRODUCION

Thank you for your purchasing the brush cutter of our Company.The present manual explains how to 

handle the brush cutter well.Before using it,please read this operator's manual carefully,operate the 

details of your machine may not agree with this manual.Please understand accordingly.

The machine is only intended to be used to cut frutex,  or soft vegetation.

Engine

Displacement (cm  )

Spark plug

Idling speed (min    )

Speed of output shaft (min   )

Max. engine output (kW)

engine output (g/kWh)(ISO 14865)

3

-1

-1

         

 39,8

NGK BPMR6A or equivalent

         

2750

        9900

         1.2

           

604

Fuel tank capacity (cm   )

3

Dry weight (kg)

Cutting attachment Type / Dia. (mm)

Sound pressure            (ISO14865)

level LpA

Equivalent

(dB (A))

Uncertainty

Measured sound

(ISO14865)

power level LwA

Equivalent

(dB (A))

Uncertainty

Measured sound

(2000/14/EC)

power level LwA (dB (A))     Racing

Guaranteed sound

(2000/14/EC)

power level LwA (dB (A))     Racing

Vibration level (m/s  ) (ISO7916)

Idling 

2

1000

Metal blade / 255

91

 3

103

  3

104

112

NOTE

Equivalent noise level/vibration level are calculated as the time-weighted energy total for noise/vibration 

levels under various working conditions with the following time distribution: 1/2 Idle, 1/2 racing.

* All data is subject to change without notice.

5

PRO-40SUM

Model

Backpack power unit

Unit

 6.7

10.7

Racing

Rear handle

Front handle

Rear handle

Front handle

       4.0

       6.7

       0.3  

       0.6

Содержание PRO-40SUM



















Отзывы: