Parker P2M Node 24 DO, Руководство пользователя

Страница: 8 / 16

Page 8 /15
P2M2HBVT12400
User Manual
30060921401W05
February 2018
Pneumatic Division
27031 Evreux - France
Green / Red LED Green LEDs Red LED Green / Red LED
LED
Status
Description Troubleshooting
LED
Status
Description Troubleshooting
LED
Status
Description Troubleshooting
LED
Status
Description Troubleshooting
OFF
Logic lines
not powered Check power
supply (pin's 2 & 4
on Power M-12)
OFF
Not link, no
activity Check
connection to
the Network
OFF
No error N/A
OFF
Initialization
Power supply
missing N/A
Check power
supply
ON
GREEN
Logic Power
OK N/A
ON
GREEN
Link sensed, no
activity N/A
Blinking
Invalid
configuration Check register
or object
settings
ON
GREEN
Operational N/A
ON
RED
Presence of
any fault
requiring
acknowledge Fix the issue and
acknowledge error/
power cycle the
module
Blinking
GREEN
Link sensed,
activity N/A
Single
Flash
Unsolicited
state change Reset module
(power OFF/ON)
Blinking
GREEN
Pre-operational N/A
Blinking
G/R
Firmware
Version
error Contact technical
support or change
the module Double
Flash
Sync manager
watchdog
timeout Reset module
(power OFF/ON) Single
Flash
GREEN
Safe-
operational N/A
ON Allocation
controller failure Reset module
(power OFF/ON)
If also RUN LED
turns RED, change
the module Flashing
GREEN
BOOT N/A
Flicker Booting error
detected Firmware
exception
Change the
module RED Fatal event If also ERR turns
RED, change the
module
Red LED
LED
Status
Description Troubleshooting
OFF
Standard mode
(No error active) N/A
ON
RED
One (or more)
active “o utputs
stage failure”
Check diagnostic
message through
the Network and
relative
troubleshooting
Local Visual Diagnostic
The P2M Node 24DO module offers local diagnostics through 6 LED’s status with interpretation described in
the table below:
NOTE: Errors caused by solenoid(s) must be fixed first and then the error must be acknowledged by either one of the following actions:
•
switching OFF/ON Auxiliary power supply (once error is fixed)
•
sending the “Acknowledge Error” command **SEE Manufacturing Specific Object “System Command”
Diagnostic through network via Object “Module Error Input”
The P2M Node 24DO module offers diagnostic data transmitted to the PLC as Process Data Input or via the Manufacturing Specific
Object
“Module Error Input” :
Byte 0 Diag 7 . . . . . . . . . . . . . Diag 0
Byte 1 Reserved
Bit # Error Name Error Description
Diag 0 Ack-Required
Set if any major fault active. Outputs are switched OFF and acknowledge is required to restart
the module to normal operation
Diag 1 Auxiliary Voltage Warning Set if Auxiliary Voltage in warning range. Module keeps normal operation
Diag 2 Auxiliary Voltage Failure
Auxiliary Voltage in Error range. Outputs are switched OFF and acknowledge is required to
restart the module to normal operation
Diag 3 Temperature Warning Set if a temperature increase above warning levels is detected by the output drivers
Diag 4 Output Driver Channel Error
Set if a major fault is detected at the output stage – solenoid short circuit. Outputs are
switched OFF and acknowledge is required to restart the module to normal operation
Diag 5 Module Error
Set if an internal communication error is active. Depending on the fault the module might
require acknowledgment.
Diag 6 Outputs Stage Not Available Set if auxiliary power is missing. No acknowledge is required
Diag 7-15 Reserved These bits will be always set as 0
Index Name Data Type Access
0x2009 Module Error Input UINT Read