Parker Matrx Digital MDM Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 28

Parker Matrx Digital MDM Скачать руководство пользователя страница 28

26

A.

Inspect machine, hoses, and connections for damage, wear, and leaks, daily.

B.

Perform functional tests as described on page 23 periodically.

C.

For cleaning the outside of the machine and accessories, we recommend the use of a germicide
containing glutaraldehyde. Follow the manufacturer’s directions for use.

SERVICE

All service and repair must be accomplished at Matrx by Parker. Have your dealer return the unit to our
factory and arrange for a loaner unit for yourself.

CE Notice

The

symbol on this product indicates compliance with the Medical Device Directive of the European

Community. A "Declaration of Conformity" in accordance with the Directive has been made and is on file.
European Communities should contact the Authorized Representative listed below regarding any Medical
Device Directive (MDD) inquiries. Direct inquiries may be made to the following addresses:

Porter Regulatory Affairs:

Parker Hannifin Corporation

Porter Instrument Division

245 Township Line Road
Hatfield, PA 19440 USA
Tel: 215-723-4000

EU Authorized Representative:

Parker Hannifin Ltd
Instrumentation Products Division
Riverside Road, Pottington Business Park
Barnstaple, EX 31 1NP, England
Phone: +44 (0) 1271-313131
Fax:

+44 (0) 1271-

«
...
26
27
28

Содержание Matrx Digital MDM





























Отзывы:

Нет отзывов