Commissioning
ETH Mounting Instructions
16
192-550002N10 ETH March 2019
2.1.2.
Mounting with mounting accessories
Mounting methods: Dimensions: Permissible lateral force: please refer to ETH
catalogue http://www.Parker.com/Literature/Electromechanical
Europe/Literature/190_550017_ETH_katalog.pdf.
2.1.2.1
Cylinder mounting with mounting plates or foot
mounting brackets
If the underside of the mounting surface is not accessible, mounting plates or foot
mounting brackets are available as accessories.
The rear mounting plate cannot be fixed with inline motor configuration.
If you fix the cylinder only at the rear end (e.g. also with a rear clevis) please
respect the effective direction of the known forces. Critical are above all lateral
forces in horizontal or vertical direction.
2.1.2.2
Screw tightening torques for the mounting of the
customer’s ETH cylinder
In order to simplify the calculation of the mounting screws for fixing the cylinder in
your application, the following table gives an overview of the required screw quality
resp. the required tightening torque (including additional boundary conditions),
under the assumption that 100 % of the permissible axial force are required.
Additionally, take care that no other loads act on the screws.
If these specifications are not adhered to, the screw joint might fail.
The failure of screw joint may lead to severe injuries.
ETH032
ETH050
ETH080
M05 M10 M16 M05
M10
M20 M05
M10
M32
Option F*
M6 - 12.9
M8 - 12.9
M12 - 12.9
Screw
15.5 (3)
47 (3)
160 (3) 160 (3)(4) 160 (3)
Screw tightening torque (1) [Nm]
6
8
12
Minimum screw-in depth [mm]
Option F
M6 - A2-70
M8 - A2-70
M10 - A2-70
Screw
7.5
16
34
Screw tightening torque (1) [Nm]
9
9
16
Minimum screw-in depth [mm]
Option F
M6 - 8.8
M8 - 8.8
M10 - 8.8
Screw
9
19
39
Screw tightening torque (1) [Nm]
9
9
16
Minimum screw-in depth [mm]
Option E
Option C
M6 - A2-70
M8 - A2-70
M10 - A2-70
Screw
8
16
34
Screw tightening torque (1) [Nm]
8
12
15
Minimum screw-in depth (2) [mm]
Option E
Option C
M6 - 8.8
M8 - 8.8
M10 - 8.8
Screw
8
16
34
Screw tightening torque (1) [Nm]
8
12
15
Minimum screw-in depth (2) [mm]
Option H
Option J
Option N
M6 - A2-70
M8 - A2-70
M10 - A2-70
Screw
7
16
31
Screw tightening torque (1) [Nm]
8
11
14
Minimum screw-in depth (2) [mm]
Option H
Option J
Option N
M6 - 8.8
M8 - 8.8
M10 - 8.8
Screw
7.5
18
35
Screw tightening torque (1) [Nm]
9
12
15
Minimum screw-in depth (2) [mm]
Option B*
M6 - 12.9
M8 - 12.9
M12 - 12.9
Screw
16.5
47
160 (3) 160 (3)(4) 160 (3)
Screw tightening torque (1) [Nm]
12
12
25
Minimum screw-in depth (2) [mm]
Option G*
M6 - 12.9
M8 - 12.9
M12 - 12.9
Screw
16.5
47
160 (3) 160 (3)(4) 160 (3)
Screw tightening torque (1) [Nm]
12
12
25
Minimum screw-in depth (2) [mm]
Option R
(5)
M6 - 8.8
M8 - 8.8
M10 - 8.8
Screw
9
19
39
Screw tightening torque (1) [Nm]
9
9
16
Minimum screw-in depth (2) [mm]
