Parker ALIGN-MG-NA Скачать руководство пользователя | Manualshive

Страница: 8 / 25

background image

INSTALLATION, OPERATION, AND MAINTENANCE MANUAL ALIGN™ MULTI-GAS GENERATOR

8

1

For purity at specific flow rates and pressures please contact Parker Hannifin.

2

For humidity and temperature information outside of this range please contact Parker Hannifin.

3

For altitudes outside of this range please contact Parker Hannifin.

3.3 Overview of Components

System Specifications Cont

Outlet Gas Specifications Cont’

Phthalates

None

Max Tank Operating Pressure

115±2 psig (7.9±0.1 barg, 793 kPa)

Gas Outlets

1/4’’ NPT

Environmental Requirements

Min/Max Ambient Temperature

60°F/ 85°F (16°C/29°C)

Max Ambient Relative Humidity

2

43% at 86°F

Max Recommended Operating Altitude

3

2000 m

Electrical Requirements

Electrical Supply for ALIGN-MG-NA, ALIGN-MG-JA

230VAC ± 15%, 50/60 Hz, 1 Phase, 20A, NEMA 6-20R receptacle

Electrical Supply for ALIGN-MG-WD

230VAC ± 15%, 50/60 Hz, 1 Phase, 32A, IP44 receptacle

Power Consumption

15A@230VAC, 2500 Watts

Fuses (F1, F2)

JJS Class T, 600V, 25A, 14.2 mm Dia x 38.1 mm

IOM_PKR_Align Multi-Gas Generator_022021.indd 8

IOM_PKR_Align Multi-Gas Generator_022021.indd 8

2/17/2021 1:11:43 PM

2/17/2021 1:11:43 PM

«
...
6
7
8
9
10
...
»

Содержание ALIGN-MG-NA


























Отзывы:

Нет отзывов

Похожие инструкции для ALIGN-MG-NA

Бренд: GBC Страницы: 8

Бренд: KAPSCH Страницы: 57

Бренд: NARGESA Страницы: 33

Бренд: Oemtools Страницы: 4

Бренд: Abicor Binzel Страницы: 92

Бренд: Datavideo Страницы: 48

Бренд: Datavideo Страницы: 34

Бренд: Datavideo Страницы: 3

Бренд: Datavideo Страницы: 34

Бренд: Datavideo Страницы: 8

Бренд: Datavideo Страницы: 10

Bathomatic Basic

Бренд: Unique Automation Страницы: 10

Бренд: Additel Страницы: 139

Бренд: RainPoint Страницы: 40

Бренд: FARM-MAXX Страницы: 35

Бренд: Parker Страницы: 24

Бренд: ACS Страницы: 28

Бренд: ATD Tools Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды