Parker ALIGN-MG-NA Скачать руководство пользователя

Страница: 20 / 25

INSTALLATION, OPERATION, AND MAINTENANCE MANUAL ALIGN™ MULTI-GAS GENERATOR

7.2 Error Messages

Fault

Description

Troubleshooting

Ground Fault

• Contact Parker Technical Support for a technician to inspect

the motor.

Under

Voltage

Protection

• This error indicates low supply voltage. Check that the supply

voltage meets the requirements in Section 3.2.

• Install a voltage booster. Available from Parker Hannifin. See

Accessories in Section 8.

OC1

Overcurrent

• Contact Parker Technical Support for a technician to inspect the

motor.

Over-Voltage

• This error indicates high supply voltage. Check that the supply

voltage meets the requirements in Section 3.2.

• Install a voltage reducer. Available from Parker Hannifin. See

Accessories in Section 8.

PF1

Input Phase

Loss

• Check that the power supply meets the requirements in Table/

Section 3.2.

PF0

Output

Phase Loss

• Contact Parker Technical Support for a technician to inspect the

motor.

ESP

Input Signal

Fault

• Follow the procedure laid out in Section 7.3. If the SYSTEM

FAULT light remains on, contact Parker Technical Support.

IOM_PKR_Align Multi-Gas Generator_022021.indd 20

2/17/2021 1:12:18 PM

Содержание ALIGN-MG-NA


























Результаты поиска

Содержание ALIGN-MG-NA

Отзывы:

Похожие инструкции для ALIGN-MG-NA

Бренды по названию

Популярные бренды

Parker ALIGN-MG-NA, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ALIGN-MG-NA

Отзывы:

Похожие инструкции для ALIGN-MG-NA

Бренды по названию

Популярные бренды