Parker ACR1200 Скачать руководство пользователя

Страница: 4 / 50

ACR1200 Hardware Manual

P/N

PM08123

CHANGE NOTICE

ACR1200 Hardware Manual P/N PM08123 Version Change:

From: Version 1.01, Dated 10/31/1999
To:

Version 1.02, Dated 6/13/2000

Page 5. Figure 1a, ACR1200 Motherboard
Outline.

Corrected connector reference
designations. Added pin 1 markings to
PWR1 and PWR2 connector.

Page 6. Figure 1b, Motherboard Outline.

Added new figure for right angle JP11-
JP12 header.

Page 33. Table 2.19, ACR1200 Isolated
Power Fuses

Corrected current rating from “4 Amps” to
“2 Amps”.

Page 34. Table 2.21, ACR1200 Standalone
Power Fuses

Corrected current rating from “2 Amps” to
“4 Amps”.

ACR1200 Hardware Manual P/N PM08123 Version Change:

From: Version 1.00, Dated 9/30/1999
To:

Version 1.01, Dated 10/31/1999

Page 6, 7. Figure 1b, 1c. Motherboard
Outline.

Added new version of outline for right
angle JP11-JP12 header.

Page 21. Figure 4, ACR1200 RS-422/
RS-485 Interface Schematic.

Corrected jumpers.

ACR1200 Hardware Manual P/N PM08123 Version Change:

Version 1.00, Dated 9/30/1999, Released

Содержание ACR1200



















































Результаты поиска

Содержание ACR1200

Отзывы:

Похожие инструкции для ACR1200

Бренды по названию

Популярные бренды

Parker ACR1200, Руководство по оборудованию

Результаты поиска

Содержание ACR1200

Отзывы:

Похожие инструкции для ACR1200

Бренды по названию

Популярные бренды