manualshive.com logo in svg

Parker ACR1200, Руководство по оборудованию

Поделиться
Скачать
Parker ACR1200 Скачать руководство пользователя страница 27

 

Chapter 1, ACR1200 Motherboard Hardware Set-Up

 

 

19

ACR1200 MOTHERBOARD JUMPERS 

RS-422/485 Configuration Jumpers, continued 

 
The following tables show the configuration schemes for the ACR1200 board.  Refer to 
the User’s Guide manual, COM1/COM2 Stream Flags, Appendix B, for bit flag details.  
Refer to the following page for hardware jumper details.   
 
MUX Flags, Set-up communication type flags: 
 

MUX1 FLAG 

MUX0 FLAG 

COMM FUNCTION 

CLR (0) 

CLR (0) 

Not Used 

CLR (0) 

SET (1) 

RS-232 (Default) 

SET (1) 

CLR (0) 

RS-422/RS-485 

SET (1) 

SET (1) 

Not Used 

 
RECEIVE/TRANSMIT Flags, RS-485 flow control flags: 
 

RECEIVE 

FLAG 

TRANSMIT 

FLAG 

COMM FUNCTION 

CLR (0) 

CLR (0) 

Use for RS-485 Operation: 

(Default) 
Receiver Enabled 
Transmitter Disabled 

CLR (0) 

SET (1) 

Not Used:   

Receiver Enabled 
Transmitter Enabled 

SET (1) 

CLR (0) 

Not Used:   

Receiver Disabled 
Transmitter Disabled 

SET (1) 

SET (1) 

Use for RS-485 Operation  

Receiver Disabled 
Transmitter Enabled 
 

 

Содержание ACR1200



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды