background image

Bulletin TI-H2PEMPD-D 

 

Installation, Operation and Maintenance Manual 

 

 

Hydrogen Gas Generator H2 PEMPD series 

 

 

1-800-343-4048 

 

 www.labgasgenerators.com 

1 Safety Information  

 

 

 

 

 

 

 

 

         

Do not install and operate this equipment until the safety information and instructions in this user guide have been read and understood by 
all personnel concerned. 

 

USER RESPONSIBILITY  

FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, 
PERSONAL INJURY AND PROPERTY DAMAGE. 

 

This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product or system 
options for further investigation by users having technical expertise.    

The user, through its own analysis and testing, is solely responsible for making the final selection of the system and components and assuring 
that all performance, endurance, maintenance, safety and warning requirements of the application are met. The user must analyze all aspects 
of the application, follow applicable industry standards, and follow the information concerning the product in the current product catalogue 
and in any other materials provided from Parker or its subsidiaries or authorized distributors.    

To the extent that Parker or its subsidiaries or authorized distributors provide component or system options based upon data or specifications 
provided by the user, the user is responsible for determining that such data and specifications are suitable and sufficient for all applications and 
reasonably foreseeable uses of the components or systems.  

Only competent personnel trained, qualified, and approved by Parker Hannifin should perform installation, start-up, service and repair 
procedures.  

This equipment is for indoor use only. Do not operate outdoors.  

This equipment is not suitable for use in any Hazardous, Flammable, or Explosive environments. Hydrogen is a highly flammable gas. Keep the 
generator away from excessive heat and naked flames.  

With the exception of oxygen, any gas can cause asphyxiation in high enough concentrations. In most scenarios, however, because hydrogen 
rises and disperses so rapidly, it is unlikely to be confined where asphyxiation might otherwise occur. Always ensure that the generator is 
operated in a well-ventilated area and all of the vent ports on the rear of the generator are kept clear and free from blockages.  

Use of the equipment in a manner not specified within this user guide may result in an unplanned release of pressure, which may cause serious 
personal injury or damage.  

When handling, installing or operating this equipment, personnel must employ safe engineering practices and observe all related regulations, 
health & safety procedures, and legal requirements for safety.  

Ensure that the equipment is depressurized and electrically isolated, prior to carrying out any of the scheduled maintenance instructions 
specified within this user guide.  

Parker Hannifin cannot anticipate every possible circumstance which may represent a potential hazard. The warnings in this manual cover the 
most known potential hazards, but by definition cannot be all-inclusive. If the user employs an operating procedure, item of equipment or a 
method of working which is not specifically recommended by Parker Hannifin the user must ensure that the equipment will not be damaged or 
become hazardous to persons or property.  

Most accidents that occur during the operation and maintenance of machinery are the result of failure to observe basic safety rules and 
procedures. Accidents can be avoided by recognizing that any machinery is potentially hazardous.  

Note: Any interference with the calibration warning labels will invalidate the gas generator's warranty and may incur costs for the recalibration 
of the gas generator.  

Should you require an extended warranty, tailored service contracts or training on this equipment, or any other equipment within the Parker 
Hannifin range, please contact your local Parker Hannifin office.  

Details of your nearest Parker Hannifin sales office can be found at www.Labgasgenerators.com. 

Retain this user guide for future reference.

 

Содержание H2PEMPD-1100

































Отзывы: