background image

4

OPERATING PROCEDURES

WARNING!   For the safe operation of this machine follow the instructions given in this booklet and the training given by 

your supervisor.  Failure to do so can result in personal injury and/or damage to machine and property!

DO NOT OPERATE MACHINE IN AN EXPLOSIVE ENVIRONMENT!

NEVER USE THIS MACHINE TO PICK UP VOLATILE OR EXPLOSIVE MATERIALS!

The model shown in this manual is intended for commercial use.

PREPARATION

To prepare the machine for operation, make sure it is of correct voltage and properly assembled.  If in doubt, ask your supervisor.

1.  If the vacuum is in its upright position (page 6)

,  raise the handle while supporting the vacuum, then slowly lower the 

vacuum to the floor.

2. 

Properly install the filter bag in the vacuum: 

Lift the cover from the machine. The filter bag inlet is designed with a rubber 

gasket that fits securely over the bag adapter (page 7) in the cover.  First push the filter bag inlet over the adapter on the 

cover.  Then from the outside of the cover reach inside the adapter and push the gasket on the rest of the way.  Replace 

the filter bag when full.

OPERATION

1.  Plug the machine’s power cable into a properly grounded outlet

 (see Grounding Instructions).

2.  The foot pedal should be raised to the “BRUSH”

 position (page 8) for wide area vacuuming.

3.  Adjust the brush height 

with the lever located on the rear of the machine near the floor (page 8).

4.  Turn the vacuum switch ON 

(rocker switch on operator’s right, page 7).

5.  Turn the brush switch ON 

(rocker switch on operator’s left, page 7) 

and begin vacuuming

.

OPERATION WITH TOOLS

Three on-board tools are available for the vacuum: the dusting tool, crevice tool and turbo tool (page 6).  Twenty (20) feet of 

hose is provided which allows access to rooms without moving the machine.

1.  The brush and vacuum switches should be turned OFF.

2.  Depress the foot pedal to the “ACCESSORY” position.

3.  Remove the rigid portion of the accessory hose 

 from its storage area in the handle and 

attach the tool of choice.

4.  Turn the vacuum switch ON and begin.

Note: The vacuum switch should be OFF when switching the foot pedal between the accessory and the brush positions.  

MAINTENANCE

ALWAYS turn the brush and vacuum motor switches OFF and UNPLUG the power cord from the electrical outlet before doing 

any clean-up or repairs, and when the machine is left unattended.

AFTER EACH USE:

1.  Vacuum filter bag: 

If the bag is full or damaged install a new one.

Filter Bag, 10 Pack – Part Number 54354

Cloth Bag (optional) – Part Number 54356

2.  Power cord and plug:

 Check for cuts or nicks;  if damaged, have the cord replaced at a factory authorized service center.

3.  Casters and Wheels:

 Remove any strings or debris that may restrict the free movement of the casters.

4.  Tools:

 Inspect the tools to ensure there is no obstruction of airflow.  Remove any debris found.

5.  Brush:

  Remove any strings or debris.  Replace if becomes worn or damaged.

Storage: 

The handle may be folded down and the machine stored upright to reduce storage space requirements.  Store the 

machine in a clean dry area.

Содержание LAV-30













Отзывы: