paratech 550500G2, Руководство по эксплуатации и обслуживанию

Страница: 18 / 38

c. During operation, check periodically to
determine if a fine misting of oil is present
in the air exhausting from the cylinder
ports.
d. To stop the Pakhammer operation, release
the trigger lever.
Note: When using the piercing applicators,
penetrate the work surface BEFORE
connecting the hose. This will prevent damage
to the hose coupling from Pakhammer
vibration.
2-6 SHUTDOWN.
a. At the conclusion of its use, shut off the
external air supply .
b. Hold the tool bit against a working surface
and pull the trigger lever to dissipate air in
the supply line.
c . Disconnect the air supply line from the oiler
connection.
d. Perform the after use maintenance specified
in chapter 4 and stow the Pakhammer in its
storage case in a dry environment.
Table 2-1. Operating Pressure and Tool Bit Recommendations
APPLICATION RECOMMENDED PRESSURE TOOL BIT
(See Table 2-2)
PSI BAR
Breaking concrete
Breaking hollow concrete block
Breaking car door hinges
Breaking locks
Breaking padlocks
Cutting light sheet metal
Cutting metal containers and tanks
Cutting sheet metal ducts
Cutting automobile door posts
Cutting aircraft skin
Cutting aircraft canopies
Cutting ship watertight doors
Popping rivets
Breaking ice
Breaking frozen earth
Shattering castings
Plugging leaks
Piercing aircraft skin/canopies
Piercing watertight doors 125 – 200
100 – 150
150 – 200
100 – 200
125 – 200
75 – 150
75 – 200
100 – 200
100 – 150
75 – 150
50 – 200
100 – 200
75 – 200
50 – 75
50 – 100
100 – 200
50 – 150
75 – 170
125 - 200
8.6 – 13.8
6.9 – 10.3
10.3 – 13.8
6.9 – 13.8
8.6 – 13.8
5.2 – 10.3
5.2 – 13.8
6.9 – 13.8
6.9 – 10.3
5.2 – 10.3
3.5 – 13.8
6.9 – 13.8
5.2 – 13.8
3.5 – 5.2
3.5 – 6.9
6.9 – 13.8
3.5 – 10.3
5.2 – 11.7
8.6 – 13.8
A, B
A, B, H
B, L
B, D, L
D
C, E, F, L
C, E, F, I, L
C, E, F, I, L
B, C, I, L
C, F, I, L
C, F, I, L
C, E, F, I
B, H
A, B, H
A, B, H
A, B
G
A, J, K
A, J, K
Table 2-2. Tool Bit Code (See Figure 2-2)
CODE NOMENCLATURE PARATECH PART NUMBER
A
B
C
D
E
F
G
H
I
J
K
L
Bullpoint
Chisel
Deep Panel Cutter
Lock Breaker/Cutter
Dual Cutter
Dual Cutter with Bullpoint
Plug Driver and Plug
Spade/Scraper
Heavy Duty Metal Cutter
6” Piercing Applicator
14” Piercing Applicator
Curved Metal Cutter 550586, 550588
550582, 550583
550590, 550591
550596
550592
550594
550598, 550246
550595
550273
550241
550251
550584
2-4