Paragon ERC-2 Скачать руководство пользователя страница 6

6

list of Parameters

Here is a list of the parameters that can be changed in the Second Level of programming, as well as their options and ranges.

Parameter

Display Symbol

Description

Range / Options

Display Status

dSPl

Information shown on the display during 

operation conditions

tdAy

 – time-of-day

rSP° 

 –  zone temperature (refrigerated space)

CyCl

 – cycle between time and zone temperature

Epr°

  – evaporator coil temperature

Clock Format

Clhr

Format of the time (12 or 24 hours mode)

12hr

 – AM/PM format

24hr

 – 24 hour format

Temperature Format

°dSP

Temperature degrees

°F

 – degrees Fahrenheit

°C

 – degrees Celsius

Defrost Type

dFtP

Type of defrost used in the application

eLeC

 – electric heater defrost / off cycle

hgAS

 – hot gas

Fan Status During 

Defrost

eFAN

Enable or not the fan during defrost

no

 – fan is turned off during defrost

yES

 – fan remains on during defrost

Fan Status During 

Normal Mode

CFAN

Enable or not the fan during normal 

compressor on/off mode

on

 – fan is always on during normal mode

CyCP

 – fan cycles with compressor

Defrost Interval

dFin

Type of defrost interval

TdAy

 – time-of-day setpoint

CPrn

 – compressor run time

tdEF

 – temperature initiated defrost

Minimum Compressor 

Off Time

CoFF

Minimum time that the compressor will 

remain turned off

Range: from 0 to 15 minutes

Minimum Compressor 

On Time

Con

Minimum time that the compressor will 

remain turned on

Range: from 0 to 15 minutes

Alarm Delay

Alrd

Time delay before the alarm goes off after 

the temperature fall off the two alarm 

setpoints

Range: from 0 to 59 minutes

Compressor Run Time

CPrn

Time the compressor will run between 

defrosts

Number of Defrosts

nodF

Number of defrosts per day

from 0 to 8 (0 means 1 defrost every 48 hours)

Defrost Start Time

dEF1-8

Start time of each defrost

Defrost Duration

dEFd

Defrost duration time (back-up for defrost 

termination temperature)

Range: from 0 minutes to 4 hours

Fan Delay

FAnd

Delay time for the fan after defrost (back-up 

for fan cut-in temperature)

Range: from 0 to 15 minutes

Pump Down

Pudn

Pump down duration

Range: from 0 to 59 minutes

Drip Time

driP

Drip time duration

Range: from 0 to 59 minutes

Setpoint Differential

diF°

Cut-in temperature differential Note: cut-in 

is cut-out plus differential

Range: from 1 to 25°

Temperature Initiated 

Defrost

tdEF

Temperature that will initiate a defrost cycle Range: from –40°F to 40°F or – 40°C to 4°C

Defrost Termination 

Temperature

dEF°

Temperature in the evaporator that will 

terminate the defrost cycle

Range: from 0°F to 75°F or –18°C to 24°C

Fan Cut-In 

Temperature

FAn°

Temperature in the evaporator that will turn 

the fan on after defrost

Range: from – 40°F to 60°F or – 40°C to 16°C

Low Temperature 

Alarm

Allo

Low temperature setpoint that will make the 

alarm go off and the error message appear 

on the display

Range: from – 40°F to 83°F or – 40°C to 28°C

High Temperature 

Alarm

Alhi

High temperature setpoint that will make 

the alarm go off and the error message 

appear on the display

Range: from – 40°F to 83°F or –40°C to 28°C

important Note:

  To change from degrees C to F or vice versa, the user must reprogram all the parameters that are related to the temperature.  

The unit does not convert the parameters automatically from degrees F to C or vice versa.

Содержание ERC-2









Отзывы: