background image

FCC WARNINGS

ESPRIT

708/ 718/728L/ 728/738/ 748/ 748ES

IMPORTANT INFORMATION

This equipment complies with Part 68 of the FCC rules. Inside the cover of this equipment is a label that contains,
among other information, the FCC registration number of this equipment.

NOTIFICATION TO TELEPHONE COMPANY

Upon request, customer shall notify telephone company of particular line to which the connection will be made, and
provide the FCC registration number and the ringer equivalence of the protective circuit.

FCC 

REGISTRATION NUMBER

:

5A7CAN-22633 - AL - E

RINGER EQUIVALENCE NUMBER

:

0.0B

USOC 

JACK

:

RJ31X (USA), CA31A (CANADA)

TELEPHONE CONNECTION REQUIREMENTS

Except for telephone company-provided ringers, all connections to the telephone network shall be made through standard plugs
and telephone company-provided jacks, or equivalent, in such a manner as to allow for easy, immediate disconnection of terminal
equipment. Standard jacks shall be so arranged that, if plug connected thereto is withdrawn, no interference to operation of
equipment at customer's premises which remains connected to telephone network shall occur by reason of such withdrawal.

INCIDENCE OF HARM

Should terminal equipment/protective circuitry cause harm to telephone network, telephone company shall, where
practicable, notify customer that temporary disconnection of service may be required; however, where prior notice is
not practicable, the telephone company may temporarily discontinue service if action is deemed reasonable in cir-
cumstances. In case of temporary discontinuance, telephone company shall promptly notify customer and will be
given opportunity to correct the situation.

CHANGES IN TELEPHONE COMPANY EQUIPMENT OR FACILITIES

The telephone company may make changes in its communication facilities, equipment operations or procedures,
where such actions are reasonably required and proper in its business. Should any such changes render customer's
terminal equipment incompatible with the telephone company facilities, the customer shall be given adequate notice
to effect the modifications to maintain uninterrupted service.

GENERAL

This equipment shall not be used on coin telephone lines. Connection to party line service is subject to state tariffs.

RINGER EQUIVALENCE NUMBER

(

REN

)

The 

REN

is useful to determine the quantity of devices that you may connect to your telephone line and still have all of

those devices ring when your telephone number is called. In most, but not all areas, sum of the 

REN

's of all devices

connected to one line should not exceed five (5.0). To be certain of the number of devices that you may connect to
your line, you may want to contact your local telephone company.

EQUIPMENT MAINTENANCE FACILITY

If you experience trouble with this telephone equipment, please contact facility indicated below for information on
obtaining service or repairs. The telephone company may ask that you disconnect this equipment from network until
problem is corrected or until you are sure that the equipment is not malfunctioning.

U

.

S

POINT OF CONTACT

:

Paradox U.S.
1717 Minnesota Avenue
Winter Park, Florida
32789 USA  1-800-786-9321

FCC PART

15, 

WARNINGS

INFORMATION TO USER

This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of
FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy, and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to equipment intermittently, the user is encouraged to try to correct the interference by
one or more of the following measures: (1) reorient or relocate the receiving antenna; (2) increase the separation
between the equipment and receiver; (3) connect the equipment to an outlet on a circuit other than the one to which
the receiver is connected, or (4) consult the dealer or an experienced radio/tv technician for assistance.

CAUTION

Changes or modifications not expressly approved by 

PARADOX SECURITY SYSTEMS 

could void the user's authority

to operate the equipment.

34

IM8

Содержание Esprit 718







































Отзывы: