background image

2 Installation Manual

INSTALLATION

For the reader to function correctly with the access 
control system, some programming may be 
required in the controller or control panel of the host 
system. For further instructions, refer to the 
appropriate manual. Only explanations directly 
concerning the reader’s programming will be 
included in this manual. 

SELECTING AN INSTALLATION SITE:
• Avoid wiring the reader’s cables in the same 

conduit as AC power cables, lock power or signal 
wiring.

• Reader wiring must remain a minimum of 30cm 

(12in) away from other wiring, such as wiring for 
AC power, computer data, telephones, electric 
locks, etc.

• Avoid sites within 1.1m (3.5ft) of computer 

monitors or CRTs.

• Avoid sites near sources of broad spectrum EMI 

noise, such as motors, pumps, generators, DC to 
AC converters, AC switching relays, power 
supplies, and light dimmers.

• Avoid sites near potential sources of RF signals, 

such as cellular phones, two-way radios, etc.

MOUNTING AND WIRING
After selecting a site for the reader, use the 
mounting plate as a guide to drill two holes to 
secure the mounting plate and a hole for the cable 
0.95cm to 2.54cm (0.375in to 1in) wide. Place a 
grommet around the edge of the hole for the cable. 
Prepare the reader’s cable by cutting the cable 

Содержание CR-R885-BL





















Отзывы: