manualshive.com logo in svg

Paradigm MAF 900-60S, Руководство пользователя, Страница: 11 / 19

Поделиться
Скачать
Paradigm MAF 900-60S Скачать руководство пользователя страница 11

 

9

Section 5  Installation 

 

5.1 Introduction 

This section contains unpacking, inspection, installation instructions and 
recommendations for the MAF 900-60S MCPA. It is important that the operator perform 
the following tasks correctly and in good faith. 
 

1.  Carefully read all materials in this section prior to equipment unpacking or 

installation. 

2.  Also read and review the operating instructions in Section 4 prior to installing the 

amplifier. 

3.  If applicable, carefully review the Federal Communications Commission (FCC) 

rules and regulation as they apply to your installation 

5.2 Site Survey 

Paradigm Wireless Systems recommends that a qualified individual or firms prior to 
equipment ordering or installation perform a site survey. Performing a survey will reduce 
or eliminate installation and turn-up delays caused by oversights. Attentions to power 
plant capacity, battery back up, cooling/air conditioning, AC breakers capacity, RF/DC 
cabling/breaker requirements are essential. 

5.3 Electrical Service Recommendations  

Paradigm Wireless Systems recommends that: 
 

• 

Proper AC line conditioning and surge suppression be provided on the primary AC 
input to the +27 Vdc source. 

• 

All electrical service should be installed in accordance with the National Electrical 
Code, any applicable state or local codes, and good engineering practice. 

• 

Grounding of all equipment should be in accordance to Bellcore standards. 

• 

Circuit breakers should be thermal type, capable of handling the anticipated inrush 
current. 

5.4 Air Conditioning 

Each MAF 900-60S MCPA will generate approximately 1900 BTU of heat. When using 
more than one amplifier it is recommended that a thermal analysis be performed. 
Ensuring proper cooling will extend the Mean Time Before Failure of the unit. 

5.5 Unpacking and Inspection 

This equipment (as applicable) has been operated, tested, and calibrated at the factory. 
Carefully open and remove the MAF 900-60S amplifier from the shipping container. 
Retain all packing material and shipping container in the event that the unit must be 
returned to the factory. Please perform the following steps: 
 

Содержание MAF 900-60S




















Отзывы:

Нет отзывов