ParaBody Parabody 660 Скачать руководство пользователя | Manualshive

Страница: 28 / 51

background image

28

FIGURE 30

STEP 30

• Assemble one 3/4” SLEEVE BEARING (77), one PEC CAM (24), two 3/4” FLANGE BEARINGS (76), one 1/2” WASHER (93), and one

1/2” LOW HEIGHT LOCK NUT (95), and a LEFT (19) or RIGHT PEC ARM (20) to each threaded shaft on the BEARING HOUSING
(6). See FIGURE 30.

•

SECURELY

assemble one TOMALOCK HANDLE (14) to each PEC ARM (19 & 20) using one 1/2 X 3-1/2” BOLT (90) and one 1/2” LOW

HEIGHT LOCK NUT (95) for each PEC ARM. See FIGURE 30.

• Securely assemble two 3/8” SPRING PIN ASSEMBLIES (51) to the spring pin barrels of the PEC ARMS (19 & 20). See FIGURE 30.

77

90 1/2 X 3-1/2”

24

20

76

51

93

95 LOW HEIGHT NUT

14

76

95 LOW HEIGHT NUT

19

6

«
...
26
27
28
29
30
...
»

Содержание Parabody 660




















































Отзывы:

Нет отзывов

Похожие инструкции для Parabody 660

Бренд: 3D innovations Страницы: 12

Бренд: Nautilus Страницы: 19

Бренд: York Fitness Страницы: 11

5620 lat attachment

Бренд: York Fitness Страницы: 8

Бренд: York Fitness Страницы: 16

Бренд: Adidas Страницы: 10

Бренд: Adidas Страницы: 14

Бренд: PaceMaster Страницы: 29

Бренд: Vicore Fitness Страницы: 8

Бренд: BOOTY BUILDER Страницы: 14

Бренд: Infinity Страницы: 6

GYM SYSTEM G5 CABLE MOTION

Бренд: Life Fitness Страницы: 31

Бренд: Rugged Computing Страницы: 22

Бренд: Impex Страницы: 21

Бренд: Weider Страницы: 24

Бренд: Weider Страницы: 24

Бренд: Weider Страницы: 25

Бренд: Weider Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды