ParaBody Parabody 660 Скачать руководство пользователя | Manualshive

Страница: 46 / 51

background image

• If upon completion of assembly, the HEAD PLATE (72) does not

sit on top of the first WEIGHT PLATE (105), push the HEAD
PLATE (72) down, insert the WEIGHT STACK PIN (75) and
perform several repetitions at the press station. This will relax the
cable system and prevent the HEAD PLATE (72) from lifting up.

STEP 52

• If after completing previous step, the HEAD PLATE (72) still does

not sit on top of the first WEIGHT PLATE (105) or if there is
excess slack in the cable system, adjust the two threaded ends of
the HEAD PLATE CABLE (102) accordingly and retighten the jam
nuts.

• If there is excess slack in the AB or PEC DEC cable system, adjust

the threaded end of the AB CABLE (103) accordingly and re-
tighten the jam nut.

46

72

75

105

102

FIGURE 52

STEP 53

•

Apply pressure to the bottom of one SHROUD (31) where thw “V” groove is and carefuly remove the weight stack opening on the plastic

SHROUD (31) as shown in FIGURE 53. This will be the front SHROUD (31).

FIGURE 53

•

Apply one PARABODY 425

SERIOUS STEEL

LABEL (32) to the front SHROUD (31) approximately 6-1/2” from the top as shown in FIGURE

53.

32

31

31

6-1/2”

«
...
44
45
46
47
48
...
»

Содержание Parabody 660




















































Отзывы:

Нет отзывов

Похожие инструкции для Parabody 660

Бренд: ParaBody Страницы: 13

Бренд: Paramount Fitness Страницы: 24

Бренд: Impex Страницы: 16

Бренд: BH FITNESS Страницы: 17

PM-842 MARCY PRO

Бренд: Marcy Страницы: 14

Бренд: X-plode Страницы: 4

Seattle Wooden Rower

Бренд: H2O Fitness Страницы: 19

E5500 FLEX STACKMASTER

Бренд: Weider Страницы: 11

Flex 109 Weight Bench

Бренд: Weider Страницы: 8

Platinum WECCSY78740

Бренд: Weider Страницы: 27

Бренд: ParaBody Страницы: 3

Бренд: NordicTrack Страницы: 15

Бренд: NordicTrack Страницы: 20

Бренд: ParaBody Страницы: 2

Бренд: BODYMAX Страницы: 28

Hammer Strength Linear Leg Press 8344901

Бренд: Hammer Strength Страницы: 11

Бренд: Impex Страницы: 21

Бренд: Weider Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды