ParaBody 375101 Скачать руководство пользователя

Страница: 22 / 22

FIGURE 27

STEP 27

• If upon completion of assembly, the HEAD PLATE (26) does not sit on top of the first WEIGHT PLATE (31), push the HEAD PLATE (26)

down, insert the WEIGHT STACK PIN (30) and perform several repetitions at the press station. This will relax the cable system and
prevent the HEAD PLATE (26) from lifting up.

CABLE ADJUSTMENT

• If after completing previous step, the HEAD PLATE (26) still does not sit on top of the first WEIGHT PLATE (31) or if there is excess slack

in the cable system, adjust the threaded end of the PRIMARY CABLE (33) accordingly and retighten the jam nut.

• If there is still excess slack in the cables, loosen and adjust the PULLEY attached to the slotted tab on the BENCH FRAME (2).

•

IMPORTANT!

Retighten the jam nut when adjustment is completed

• The following adjustments can be made to adjust the cable tension:

Thank you for purchasing the Parabody 375101 Home Gym. If unsure of proper use of equipment, call your

local Parabody distributor or call the Parabody customer service department at (800) 328-9714.

ADUST!

Содержание 375101























Результаты поиска

Содержание 375101

Отзывы:

Похожие инструкции для 375101

Бренды по названию

Популярные бренды

ParaBody 375101, Руководство по сборке

Результаты поиска

Содержание 375101

Отзывы:

Похожие инструкции для 375101

Бренды по названию

Популярные бренды