4
CAUTION!
To de-energize the outputs of the UPS:
1. If the UPS is on press and release the On/Off/Test button.
NOTE:
Turn the
input circuit breaker (on the rear panel) off for the 208V models.
2. Disconnect the UPS from the AC wall outlet.
3. To de-energize the UPS completely, disconnect the battery.
ON / OFF / TEST BUTTON:
Press and release the On/Off/Test
button during the audible alarm's first beep to turn the UPS On.
Once the UPS successfully passes the twenty second self-test the
load will be powered.
NOTE:
The input circuit breaker (on the rear
panel) MUST be in the on position for the 208V models.
Press and release the On/Off/Test button during the audible alarm's
first beep to turn the UPS Off. The UPS will continue to charge the
batteries whenever it is plugged into a wall outlet and there is an
acceptable AC voltage present.
To perform a ten second battery test: With the UPS in the AC
normal mode, press and hold the On/Off/Test button until the audible
alarm sounds four beeps, and then release. During the test, the
UPS will switch to the Battery mode, the On-Battery icon will
illuminate, and the alarm will sound.
NOTICE:
This equipment has been tested and found to comply with the limits for a
Class B computing device in accordance with the specifications in Subpart J of Part
15 of FCC Rules and the Class B limits for radio noise emissions from digital
apparatus set out in the Radio Interference of the Canadian Department of
Communications. These limits are designed to provide reasonable protection
against such interference in a residential installation. This equipment generates and
uses radio frequency and if not installed and used properly, that is, in strict
accordance with the manufacturer's instructions, this equipment may cause
interference to radio and television reception. If this equipment does cause
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
Reorient the receiving antenna.
Relocate the computer with respect to the receiver.
Move the computer away from the receiver.
Plug the computer into a different outlet so that the computer and receiver are on
different branch circuits.
Shielded communications interface cables must be used with this product.
WARNING:
Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user's authority to operate the
equipment.
NOTE:
These UPSs are shipped with the batteries disconnected. The batteries
must be connected before putting these UPSs into service. Refer to Section 3
"Installation" for connecting the batteries.
5
Receiving Inspection
After removing your UPS from its carton, it should be inspected for damage
that may have occurred in shipping. Immediately notify the carrier and
place of purchase if any damage is found. Warranty claims for damage
caused by the carrier will not be honored. The packing materials that your
UPS was shipped in are carefully designed to minimize any shipping
damage. In the unlikely case that the UPS needs to be returned to the
manufacturer, please use the original packing material. Since the
manufacturer is not responsible for shipping damage incurred when the
system is returned, the original packing material is inexpensive insurance.
PLEASE SAVE THE PACKING MATERIALS!
Life Support Policy
As a general policy, we do not recommend the use of any of our products in
life support applications where failure or malfunction of the product can be
reasonably expected to cause failure of the life support device or to
significantly affect its safety or effectiveness. We do not recommend the
use of any of our products in direct patient care. We will not knowingly sell
our products for use in such applications unless Para Systems receives, in
writing, assurances satisfactory to us that (a) the risks of injury or damage
have been minimized, (b) the customer assumes all such risks, and (c) our
liability is adequately protected under the circumstances.
© COPYRIGHT 2020 BY PARA SYSTEMS, INC.
All Rights Reserved. All rights of this User Manual (“Manual”), including but
not limited to the content, information, and figures are solely owned and
reserved by Para Systems, Inc. (“Para Systems”). The Manual can only be
applied to the operation or the use of this product. Any disposition,
duplication, dissemination, reproduction, modification, translation, extraction,
or usage of this Manual in whole or in part is prohibited without the prior
written permission of Para Systems. Given that Para Systems will
continuously improve and develop the product, changes may be made to the
information in this Manual at any time without obligation to notify any person
of such revision or changes. Para Systems will make all possible efforts to
secure the accuracy and the integrity of this Manual. Para Systems
disclaims any kinds or forms of warranty, guarantee, or undertaking, either
expressly or implicitly, including but not limited to the completeness,
faultlessness, accuracy, non-infringement, merchantability, or fitness for a
particular purpose of the Manual.
