Panduit VS-AVT-C02-L03 Скачать руководство пользователя страница 21

© Panduit Corp. 2018 

INSTRUCTION MANUAL 

VeriSafe AVT 

 

B21052_08 

Page: 20 of 20 

7-2018 

Warranty

 

 

Panduit Limited Product Warranty 

 

1. 

Limited Product Warranty

. For purposes of this Limited Product Warranty, “

Panduit products” 

mean all Panduit-branded products that 

Panduit sells. Unless a different time period is set forth in the Panduit product manual, user guide or other product documentation, Panduit 

warrants that the Panduit product, and each part or component of the Panduit product, will comply with Panduit’s published specifications 

and will be free from defects in material and workmanship for a period of 1 year from the date of invoice from Panduit or its authorized 

distributor, not to exceed 18 months from the original date of shipment from Panduit’s facility.  

 

2. 

Firmware. 

Unless otherwise provided in a separate license agreement, and subject to the limitations for third-party products set forth 

below, Panduit warrants that any firmware contained in any Panduit products, when used with Panduit-specified hardware and when 

installed properly, will perform in accordance with the Panduit published specifications for a period of 1 year from the date of invoice from 

Panduit or its authorized distributor, not to exceed 18 months from the original date of shipment from Panduit’s facility. Any exceptions to 

this 1 year warranty period will be identified in the Panduit product manual, user guide or other product documentation. Panduit does not 

warrant that the operation of the firmware will be uninterrupted or error-free, or that the functions contained therein will meet or satisfy 

Buyer’s intended use or requirements. Any warranties, if any, that Panduit provides for any standalone software that Panduit sells will be 

stated in the applicable End User License Agreement.  

 

3. 

Remedies

. Panduit’s sole and exclusive obligation and Buyer’s exclusive remedy under this warranty is Panduit’s repair or replacement 

of the defective Panduit product. Panduit shall have sole discretion as to which of these remedies Panduit will provide to Buyer. Buyer 

requested on-site warranty service is not covered and will be at Buyer’s sole expense, unless authorized in writing by Panduit in advance 

of the commencement of the on-site warranty service. Panduit has the right to either examine the Panduit products where they are located 

or, in its sole discretion, issue shipping instructions for return of the product. Where applicable, Buyer must return the defective product, 

part or component, transportation prepaid to Panduit’s customer service department accompanied by Panduit’s Return Material 

Authorization. If Panduit confirms that there is a defect that is covered by this warranty, the repaired or replaced Panduit product will be 

warranted for the remainder of the warranty period applicable to the originally shipped Panduit product, or for a period of 90 days from 

the date of shipment to Buyer, whichever is longer.  

 

4. 

No Warranty for Third-Party Products. 

Panduit makes no representations and disclaims all warranties of any kind, express or implied 

relative to any third-party product or services, including any third-party software or firmware, which may be incorporated into a Panduit 

product and/or resold or sublicensed by Panduit

To the extent any warranties extended to Panduit by the third-party manufacturer are 

transferable, Panduit will transfer such warranties to Buyer and any enforcement of such third-party warranties shall be between the Buyer 

and the third-party

Panduit does not warrant the compatibility of the Panduit products with the products of other manufacturers or Buyer’s 

application except to the extent expressly represented in Panduit’s published specifications or written quotation.  

 

5. 

Exclusions

. Before using, Buyer shall determine the suitability of the Panduit product for his intended use and Buyer assumes all risk and 

liability whatsoever in connection therewith. The warranties contained herein shall not apply to any Panduit products that have been 

subjected to misuse, neglect, improper storage, handling, installation or accidental damage or modified or altered by persons other than 

Panduit or persons authorized by Panduit. In addition, the firmware warranty does not cover any defects resulting from Buyer-supplied 

firmware or unauthorized interfacing, operation outside of the environmental specifications for the products, or improper or inadequate 

site preparation or maintenance by Buyer. Panduit products are not designed, intended or authorized to be used in medical applications 

or as components in medical devices that are used to sustain or support human life. Should Buyer purchase or use a Panduit product for 

any such unintended or unauthorized medical application, Buyer shall indemnify and hold Panduit harmless from any liability or damage 

whatsoever arising out of the use of Panduit products in such medical applications.  

 

6. 

LIMITATION ON LIABILITY. THE WARRANTIES PROVIDED HEREIN ARE BUYER’S SOLE AND EXCLUSIVE WARRANTIES. ALL IMPLIED 

WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR 

USE ARE DISCLAIMED. TO THE EXTENT PERMITTED BY LAW, IN NO EVENT SHALL PANDUIT BE LIABLE FOR ANY LOSS OR DAMAGES 

ARISING FROM ANY PANDUIT PRODUCT WHETHER DIRECT, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR SPECIAL, INCLUDING WITHOUT 

LIMITATION ANY CLAIM FOR LOSS OF DATA, LOSS OF ACTUAL OR ANTICIPATED REVENUE, PROFITS OR SAVINGS. 

 

 

7. 

General

. This Limited Product Warranty applies to the Panduit products only and not to any combination or assembly of the Panduit 

products. Nothing in this Limited Product Warranty shall be construed to provide Buyer with a warranty for any system implementation 

using Panduit products. The Panduit Certification Plus System Warranty is available for projects that are installed by Panduit Certified 

Installers, meet various requirements and are registered with Panduit in accordance with the terms of the Panduit Certification Plus System 

Warranty.  

 

Содержание VS-AVT-C02-L03






















Отзывы: