Panduit Smartzone UPS INTELLIGENT NMC Скачать руководство пользователя страница 36

Страница: 36 / 97

INTELLIGENT NMC USER MANUAL

Switching an Outlet Group On or Off

This is only applicable to outlet group switched UPSs. Outlets Groups on the switched
UPS models are easily switched on, switched off, or rebooted. This action requires the
user to have Administrator or Controller Privileges.

Enabling Manual Outlet Group Control

1. Select the Home Icon then Control & Manage from the drop-down menu in the

Web GUI

2. In the Control & Manage and select, the

Outlet Groups

tab.

3. Select the pencil next to

Outlet Group Control

Figure 41: Outlet Group Control

4. Select

Enable

in the pull down to enable manual outlet group control or

Disabled

to disable manual outlet control

Changing the state of the outlet group

1. Select the Home Icon then Control & Manage from the drop-down menu in the

Web GUI

2. In the Control & Manage and select, the

Outlet Groups

tab.

3. Select the outlet group by clicking on the pencil icon on the right.
4. Select the desired

Power Control

from the dropdown menu.

5. Select Save.

Note

: If outlet group 1 is off, all other outlet groups will automatically be turned off.

For example, if you reboot outlet group 1, outlet group 2 will be rebooted.

Available power control options:

Off Orderly: Send shutdown commands to all smart loads on the outlet group,
wait

“Off Delay”, then remove power from the outlet group.

Off: Immediately remove power from the outlet group.

Off Delayed: Wait

“Off Delay” then remove power from the outlet group.

Содержание Smartzone UPS INTELLIGENT NMC


































































































Результаты поиска

Содержание Smartzone UPS INTELLIGENT NMC

Отзывы:

Бренды по названию

Популярные бренды

Panduit Smartzone UPS INTELLIGENT NMC, Руководство пользователя

Результаты поиска

Содержание Smartzone UPS INTELLIGENT NMC

Отзывы:

Бренды по названию

Популярные бренды