25
24
U S E R M A N U A L
P A N D O R A D X L 1 9 2 0 L / 1 9 3 0 L C A R S E R V I C E - S E C U R I T Y S Y S T E M
LED
indicator flash confirm the input of the second digit. Then you can enter the next digit.
• Enter the third digit of the code using
VALET
button. Press the button a number of times, equals
to the third digit. Pauses between presses should not exceed 1 second. Each pressing will be
confirmed with an orange
LED
indicator flash. A Pause for more than 1 second and a red
LED
indicator flash confirm the input of the third digit. Then you can enter the next digit.
• Enter the fourth digit of the code using VALET button. Press the button a number of times, equals
to the fourth digit. Pauses between presses should not exceed 1 second. Each pressing will be
confirmed with an orange
LED
indicator flash. The system will confirm correct PIN-code with the
series of red and green flashes and the system will enter programming mode. If the input was
incorrect, it will be indicated with a red
LED
indicator flash and the system will stay in a previous
state. New input can be attempted after 5 seconds.
Exit programming mode:
To exit programming mode turn on the ignition or turn off power of the base unit. The system will
reboot programmatically (all changes will be saved) after exiting programming mode using ignition. All
ways to exit the programming menu are accompanied by sound signals of the siren and light signals of
the LED indicator. Light signals indicate the number of recorded devices: first green flashes indicate the
number of recorded radio tags, red flash indicates registered mobile device.
Status indicator lights during PIN-code entering:
Short orange flash
Confirmation of
VALET
button pressing
Short red flash
Confirmation of entering a PIN-code digit
Red and green flashes
PIN-code is correct
Long red flash
PIN-code is incorrect
Preparing to program the system using a computer
The system allows programming all settings and updating software of the base unit via micro-
USB cable. If the base unit has not been installed in the vehicle yet, it will be powered via micro-USB
cable while programming. To program using a computer, you need a standard USB cable, a computer
with Windows XP/Vista/7/8/10 and Pandora AlarmStudio application (you can download it from
pandorainfo.com).
It is required to create an account in AlarmStudio to use Pandora CLONE for remote engine start (you
can register without a connection to a system). Pandora CLONE procedure requires Internet connection.
In preparation to the programming these stages should be followed:
• connect the system and PC via USB cable;
• start Pandora AlarmStudio;
• enter the programming settings mode by entering the service PIN-code.
Updating firmware
It is recommended to update firmware of the base unit before installing and programming the
system (actual vesion of the firmware you can download from
pandorainfo.com
). You can update
firmware using AlarmStudio application after entering programming mode or using quick boot
algorithm (PIN-code is not required).
Quick boot mode: open AlarmStudio; de-energize and disconnect the system; press and hold
VALET
button located on the base unit; release the button immediately after connecting the system
and a computer via USB cable; the system will enter boot mode.
If the boot mode has been interrupted for some reason and the status indicator lights red, you need
to load firmware using quick boot mode (without entering PIN-code).
Programming using VALET button
The system allows programming some settings using
VALET
button. To configure all settings
use a computer to program the system.
Enter programming mode by entering the “Service PIN-code“, Use
VALET
button to enter the
desired level number (press the button a number of times, equal to level number; pauses between
presses should not exceed 1 second). The system will confirm correct input with red
LED
flashes
and short sound signals of a siren and proceed to the desired level. If the input was incorrect, the
system will not confirm input and will await a new level input after a series of green and red flashes
Level 1
Recording remotes and radio tags into the system memory
Level 2
Changing the factory preset of the service PIN-code
Level 3
Recording the idle speed to the system memory
