background image

 

 

WARNING!!!

– 

       

                                                                                                 

      

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

   

 

   

 

 

 

 

 

 

 

     

 

   

 

 

 

 

 

 

 

                  

 

  

{

: OFF

 

   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

:  ON

OFF 

ON 

page 8

First start of the hood.

Remote control synchronization.

Once installed the hood and the electrical connection to the main power, switch on the main power
switch in the connections box and we synchronize the remote control. The process is as follows:

Open the panel that covers the filter, extract the filter. It can see the connection box. On the side of 
the box or just above, we can find the main power switch and start of the hood. Press the ON position 
(see position junction box and switch on drawing, depending on the model or versions).

(Once started follow the synchronization instructions of the remote control)

Once put the switch in ON position and before 15 seconds, it should pressing or holding the 
light button on the remote control facing the hood. Then the light will turn on the hood and it will 
confirm that synchronization was successful.

Light button

Light button

The remote control synchronization with hood can be lost due to not making the synchronization 
process well before 15 seconds after the switch on, due to power outages or variations on the 
electrical network, causing the hood doesn't respond to remote control commands, so it must be 
synchronize again.

* Synchronizing the remote control with the hood: 

1 - Disconnect the house's main power or the connection box that feeds the hood (OFF). 
2 - Reconnect the house's main power or the connection box that feeds the hood (ON). 
3 - WARNING: Once the 2nd step was done, before within 15 seconds, face the remote control
 the hood and press or hold down the command *LIGHT button. 
4 - Then, head lights will light in the hood, so the code for the remote control has been 
registered by the hood and is already synchronized.

Содержание E-220













Отзывы: