manualshive.com logo in svg
background image

Pick-up Device:

771 (H) x 492 (V) pixels, Interline Transfer CCD

Scanning Area:

4.8 (H) x 3.6 (V) mm (Equivalent to scanning area of
1/3” pick-up tube)

Scanning:

525 lines/60 fields/30 frames

Horizontal:

15.734 kHz

Vertical:

59.94 Hz

Synchronization:

Internal, Line-locked, External (VS/VBS) or 
Multiplexed Vertical Drive (VD2) selectable

Video Output:

1.0 V[p-p] NTSC composite 75 

/BNC connector

Horizontal Resolution:

480 lines

Signal-to-Noise Ratio:

50 dB (AGC OFF, weight ON)

Dynamic Range:

46 dB

Minimum Illumination:

0.4 lx (0.04 footcandle) at F0.75 [Equivalent to 0.8 lx
(0.08 footcandle) at F1.4]

Gain Control:

AGC ON or OFF (SET UP MENU) selectable

White Balance:

ATW or AWC (SET UP MENU) selectable

Aperture:

Set Variable (SET UP MENU)

Electronic Light Control:

Equivalent to continuous variable shutter speeds
between 1/60 s and 1/10 000 s

Super Dynamic

2

:

ON or OFF (SET UP MENU) selectable

Electronic Shutter Speed:

1/60 (OFF), 1/100, 1/250, 1/500, 1/1 000,1/2 000,
1/4 000, 1/10 000 s selectable

Lens Mount:

C-mount or CS-mount selectable

ALC Lens:

DC or Video selectable

Ambient Operating Temperature:

–10°C - +50°C (14°F - 122°F)

Ambient Operating Humidity:

Less than 90 %

Power Source and

WV-CP460:

120 V AC 60 Hz, 4.8 W

Power Consumption:

WV-CP464:

24 V AC 60 Hz, 4.9 W
12 V DC, 490 mA

Dimensions (without lens):

74 (W) x 55 (H) x 123 (D) mm
[2-15/16” (W) x 2-3/16” (H) x 4-13/16” (D)]

Weights (without lens):

WV-CP460:

0.41 k

g

(0.9  lbs.) (without power cord)

WV-CP464:

0.4 k

g

(0.9  lbs.)

Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.

SPECIFICATIONS

OPTIONAL ACCESSORIES

Lenses :

WV-LA2R8C3B, WV-LA4R5C3B, WV-LA9C3B, WV-LA210C3, WV-LA408C3
WV-LA908C3, WV-LZ61/10, WV-LZ61/15, WV-LZ62/2, WV-LZ62/8,
WV-LF4R5C3A, WV-LF9C3A

STANDARD ACCESSORIES

Body Cap.....................................................................1 pc.
ALC Lens Connector (YFE4191J100)..........................1 pc.
AC Power Cord (only WV-CP460) ...............................1 pc.

© Matsushita Communication Industrial Co., Ltd. 2000

Panasonic Security and Digital Imaging Company

A Division of Matsushita Electric Corporation of America

Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094

Regional Offices:

Northeast: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303

Southern: 1225 Northbrook Parkway, Suite 1-160, Suwanee, GA 30024 (770) 338-6838

Midwest:

1707 North Randall Road, Elgin, IL 60123 (847) 468-5211

Western:

6550 Katella Ave., Cypress, CA 90630 (714) 373-7840

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada (905)624-5010

Panasonic Sales Company
Division of Matsushita Electric of Puerto Rico Inc.

Ave. 65 de Infanteria. Km. 9.5
San Gabriel Industrial Park, Carolina,
Puerto Rico 00985 (809)750-4300

Содержание WVCP460 - COLOR CCTV CAMERA












Отзывы: