background image

4

Precautions for installation

Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper 
installation or operation inconsistent with this documentation.

The installation should comply with local electrical 
code.

Before start the installation/connection, check and prepare 
the required devices and cables. Before starting the con-
nection, turn the power of the devices including the camera 
and the PC off.

Refer installation work to the dealer. Failure to 
observe this may cause fire, electric shock, injury, or 
damage to the product.

Power supply

Use a power supply device equipped with the ON-OFF 
switch for servicing. When the power cord of the product is 
connected to the power supply device, the power will be 
supplied to the product. When the product is supplied, the 
product will perform panning, tilting, zooming and focusing. 
Before cleaning the product, make sure that the power 
cable is not connected to the main power supply.

Installation area for this product

Consult the dealer about the installation area to select a 
strong wall area.

•  Screws used for installing this product on a wall are not 

supplied. Prepare them according to the material and 
strength of the area where the product is to be installed.

 

Recommended screw*: M10 x 4 pcs.

 

Minimum pull-out strength (per 1 pc.): 823 N {185 lbf}

 

*When using “M8” screws, make sure to prepare 4 plain 
washers and use them together.

•  Do not mount the product on a plaster board or a 

wooden section because they are too weak. If the prod-
uct is unavoidably mounted on such a section, the sec-
tion shall be sufficiently reinforced.

Mounting method for this product

This product is designed to be used as a pendant mount 
camera. If the product is mounted on a desktop or at a 
slant, it may not work correctly and its lifetime may be 
shortened.

Protection from lightning

When cables are used outdoors, there is a chance that they 
may be affected by lightning. In this case, install a lightning 
arrester just before where the cables connect to the cam-
era.

Do not place this product in the following places:

•  Locations where a chemical agent is used such as a 

swimming pool

•  Locations subject to moisture or oil smoke such as a 

kitchen

•  Locations that have a specific environment that is sub-

ject to an inflammable atmosphere or solvents

•  Locations where radiation, x-ray, intense radio wave, or 

strong magnetism is produced

•  Locations where corrosive gas is produced, locations 

where it may be damaged by briny air such as sea-
shores

•  Locations where the temperature is not within the spec-

ified range (–50 °C to +55 °C {–58 °F to 131 °F})

•  Locations subject to vibrations, such as on vehicles, 

marine vessels, or above product lines (This product is 
not designed for onvehicle use.)

•  Locations subject to condensation as the result of 

severe changes in temperature (In case of installing the 
product in such locations, the dome cover may become 
foggy or condensation may be caused on the cover.)

Screw tightening

•  The screws and bolts must be tightened with an appro-

priate tightening torque according to the material and 
strength of the installation area.

•  Do not use an impact driver. Use of an impact driver 

may damage the screws or cause tightening exces-
sively.

•  When a screw is tightened, make the screw at a right 

angle to the surface. After tightening the screws or 
bolts, perform checks to ensure that the tightening is 
sufficient enough so that there is no movement or 
looseness.

The protection cover attached to the camera unit 
shall be removed after completion of the installation.  
(rain wash coating model)

Make sure to remove this product if it will no longer 
be used.

Take notice of humidity.

Install this product when the humidity is low. If this product 
is installed during rainfall or at a high humidity, the inside 
may be exposed to moisture and the dome cover may 
become foggy.

Matters you should know at installation work

Compatibility of devices are restricted. Before connections, 
check the ratings and dimensions of the devices to be 
used. Refer to the catalog or contact your dealer for further 
information.

Содержание WV-Q122A

















Отзывы: