background image

13

Step 4

When attaching the camera to the housing base, the posi-
tioning pin shall be on the "REAR" side.
Make sure that the camera is securely attached to the 
mount bracket by turning the bracket counterclockwise 
(seen from below).
Tighten them firmly with the 3 screws* that have been 
removed in Step 1.
* Special screw (fixing screw): These screws are hexagon 

screws. Use a hexagon wrench.

  There are 2 types of wrenches to be used; one is hexago-

nal wrench "for M5" (WV-SW598) and the other is hexago-
nal wrench "for M6". Refer to the Operating Instructions of 
the camera for the wrench to be used, which depends on 
models.

  (Recommended tightening torque (for common use in M5 

and M6): 2.45 N·m {1.81 lbf·ft})

* The illustration above is provided for describing the top of 

the camera, and therefore, this bracket is omitted.

Fixing screws (3 pcs.)

Housing base

Positioning 

pin

Camera

Protection cover

Step 5

Mount the front and rear sunshields, and then remove the 
protection cover.
Refer to the Operating Instructions of the camera for further 
information.
Removal of the protection cover is described only for rain 
wash coating model.

START

Front/rear sunshields 

(supplied with the camera)

Housing base

Содержание WV-Q122A

















Отзывы: