![background image](http://html1.mh-extra.com/html/panasonic/wv-cw594/wv-cw594_installation-manual_4250441010.webp)
10
Precautions for installation
The following points as well as the contents of
"Warning" and "Caution" shall be observed.
Panasonic assumes no responsibility for injuries or
property damage resulting from failures arising out
of improper installation or operation inconsistent
with this documentation.
Installation work shall be performed in accordance with
the technology standard of the electric installation.
Installation Location
• Install the camera on a concrete ceiling or wall at a
location that is sufficiently strong to support it.
• For wall mounting, use the optionally available (WV-
Q122) Wall Mount Bracket.
• Bolts for mounting the ceiling mount Attachment
Pipe to a ceiling or wall are not provided. You need
to purchase them separately in accordance with the
materials and strength of the place you are
installing the camera.
This camera is designed for use in a hanging configuration
only.
Install the camera in a horizontal configuration, with
the dome pointed downwards.
For wall mounting, use the optionally available (WV-Q122)
Wall Mount Bracket. Use the Screws recorded in the table
as below. Screws are not provided, and they should be
prepared in accordance with the materials, structure and
gross weight of the place you are installing the camera.
Mounting conditions
This
camera
Applicable mount bracket
Joint portion to ceiling or
wall surface
Weight Model Weight
Installation
position
Recommen-
ded screw
Screw
quantity
Minimum pull-out
strength (per 1 pc.)
Approx.
4.5 k
g
WV-Q122
Approx.
2 k
g
On wall
M8
4
pieces
823 N
{84 k
g
f}
• Ensure that the mounting surface, anchor and
screws are sufficiently strong.
• Do not mount this product on a plaster board or a
wooden section because they are too weak. If this
product is unavoidably mounted on such a section,
the section shall be sufficiently reinforced.
Avoid installing this product in the following locations.
• Locations where a chemical agent is used such as
a swimming pool.
• Locations subject to steam and oil smoke such as a
kitchen, Locations near flammable gas or vapor.
• Locations where radiation or x-ray emissions are
produced.
• Locations where corrosive gas is produced,
Locations where it may be damaged by briny air
such as seashores.
• Locations where the temperature is not within
–50 °C to +50 °C.
• Locations subject to vibrations (This product is not
designed for on-vehicle use.)
• Locations subject to condensation as the result of
severe changes in temperature (In case of installing
the product in such locations, the dome cover may
become foggy or condensation may be caused on
the cover.)
Avoid moist or dusty places to install this product.
Otherwise, lifetime of the internal parts may be
shortened.
Avoid installing this product in a place with a high
level of noise.
Installation near an air conditioner, an air cleaner, a
vending machine, or the like causes noise.
Remove the cover film from the dome section of the
dome cover after the installation is complete.
Be sure to remove this product if it is not in use.
Keep this product cable away from the lighting cable.
Conduct the power distribution work to keep a distance
of 1 m or more from the 220 V - 240 V power line. Or
conduct the electric conduit work separately.
Failure to observe this may cause noise.
Radio interference
When this product is used near TV/radio antenna,
strong electric field or magnetic field (near a motor or a
transformer), images may be distorted and noise sound
may be produced. In such a case, run the camera
cable through specialized steel conduit tubes.
Note:
• Select a place that is strong enough for the
installation. If you install the camera on a ceiling or
wall, except for accidents caused by fault in the
c a m e r a , P a n a s o n i c h o l d s a b s o l u t e l y n o
responsibility for accidents caused by the camera
falling due to unsuitable installation. Take sufficient
care when installing the camera. If the installation
is not strong enough, be sure to sufficiently
reinforce the location and check that it is safe.
• To prevent the camera from falling, attach the
safety wire to the mounting bracket or the anchor
bolt before starting to install the camera to prevent
it from falling.
• Always request installation work from a qualified
service person or system installer. Lack of technical
knowledge creates the risk of fire, electric shock,
personal injury, and material damage.