Panasonic WH-SXC09F3E8 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 161

background image

44

* note: - Two-way Valve shall be CE marking compliance component.
- Maximum load for the valve is 9.8 VA.

5 Three-Way Valve shall be spring and electronic type. Valve cable shall be (3 × min 0.5 mm

2

), of type

designation 60245 IEC 57 or heavier, or similarly double insulation sheathed cable.
* note:  - Should be CE marking compliance component.
          - It should be directed to heating mode when it is OFF.
          - Maximum load for the valve is 9.8 VA.

6 Room Thermostat cable must be (4 or 3 × min 0.5 mm

2

), double insulation layer of PVC-sheathed or rubber-

sheathed cable.

7 Tank OLP cable must be (2 × min 0.5 mm

2

), double insulation layer of PVC-sheathed or rubber-sheathed

cable.
* note: - if such connection deemed NO necessary for tank OLP, please connect jumper between terminal

no. 13 and 14.

8 Tank Sensor shall be resistance type, please refer to Graph 5.1 for the characteristic and details of sensor.

Its cable shall be (2 × min 0.3 mm

2

), double insulation layer (with insulation strength of min 30 V) of PVC-

sheathed or rubber-sheathed cable.

9 External Controller shall be connected to 1-pole switch with min 3.0mm contact gap. (connection refer to

Diagram 5.2). Its cable must be (2 × min 0.5 mm

2

), double insulation layer of PVC-sheathed or rubber-

sheathed cable.
* note:  - When making such connection, kindly remove the jumper between terminal no. 17 and 18.
          - Switch used shall be CE compliance component.
          - Maximum operating current shall be less than 3A

rms

.

10 Must install Solar Connection PCB (optional) to indoor unit when Solar Pump Station is utilized. Refer

Solar Connection PCB’s installation instruction for detail of installation.

11 Solar Three-way Valve cable shall be (3 × min 0.5 mm

2

), double insulation layer PVC-sheathed or rubber-

sheathed cable.

12 Solar Pump Station cable shall be (2 × min 0.5 mm

2

), of double insulation PVC-sheathed or rubber-sheathed

cable. Strongly recommended install with maximum length of 10 meter only.

Tank

OLP

Cable

Terminals on the indoor

Lead wire cord

1 2 3 4 5 6

Three-way

Valve Cable

Two-way

Valve Cable

Solar Pump

Station Cable

External

Controller

Cable

7 8 9 10 11 12

13 14 15 16 17 18

19 20 21

22 23

Booster Heater

Cord

Room Thermostat

Cable

Solar Three-way

Valve Cable

Only if Solar Connection PCB installed

*Cooling model only

*Cooling model only

Tank

Sensor

Cable

HE

AT

COOL

N

N

L

L

N

N

O

PEN

O

PEN

CLO
SE

CLO
SE

N

CLO
SE

O

PEN

LN11

N

L

N

L 22

P OWER SUP PLY 2

L B1

L B2

L B3

N

POWER SUP PLY 1

L A1

L A2

L A3

N

45

A

How to guide the lead wires and power supply cord

(view without internal wiring)

Bind all optional

cables and cords

with this band
Power Supply 2

RCCB/ELCB

Earth wire must be longer than other

cables for safety reasons.

Bind all optional cables and cords with this ba
Holder (Clamper)

Power Supply 1

3 phase RCCB

Power Supply 2

3 phase RCCB

Earth wire must

be longer than

other cables for

safety reasons.

Indoor unit bottom

Holder

(Clamper)

Power

Supply 2

Power

Supply 1

Power

Supply 2

Connecting

cables

Bushing

Indoor terminal for

connecting cables

(Only applicable for model

WH-S**09*3E8)

(Only applicable for model

WH-S**09/12/14/16*9E8)

«
...
42
43
44
45
46
...
»

Содержание WH-SXC09F3E8


































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WH-SXC09F3E8

Бренд: DAB Страницы: 13

Бренд: Eaton Страницы: 12

Бренд: Barnes Страницы: 12

Бренд: Radiatori 2000 Страницы: 2

Бренд: veito Страницы: 28

Бренд: Wangen Страницы: 72

Бренд: Kärcher Страницы: 18

Бренд: L.B. White Страницы: 28

Бренд: L.B. White Страницы: 68

Бренд: L.B. White Страницы: 34

Бренд: L.B. White Страницы: 28

Бренд: L.B. White Страницы: 4

Бренд: Zibro Страницы: 16

Бренд: Zibro Страницы: 17

Бренд: CIAT Страницы: 35

Бренд: Calpeda Страницы: 72

LEADER ECOTRONIC Series

Бренд: DAB PUMPS Страницы: 10

Бренд: King Electrical Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды