Panasonic VL-VN1800 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 68

background image

Note

After the Control Box is initialised, you must configure the mandatory settings with Quick Setup Wizard.
For details refer to "5.4.1 Quick Setup Wizard".

1.

Slide the System Mode Switch to the "SYSTEM INITIALIZE" position.

A

B

A. STATUS Indicator

B. System Mode Switch

2.

Turn on the power switch of the Control Box. The STATUS indicator will flash green.

3.

While the STATUS indicator is flashing green, slide the System Mode Switch back to the "NORMAL"
position. Depending on the configuration, initialisation takes about 2.5 minutes. If successfully executed,
the STATUS indicator will stop flashing and remain lit up.

4.5 Starting the Control Box

Installation Manual

39

«
...
37
38
39
40
41
...
»

Содержание VL-VN1800





































































Отзывы:

Нет отзывов

Похожие инструкции для VL-VN1800

Бренд: Mackie Страницы: 6

Бренд: Mackie Страницы: 6

Бренд: Mackie Страницы: 12

Fussion Series 3000

Бренд: Mackie Страницы: 8

Fussion Series 3000

Бренд: Mackie Страницы: 8

Art Series ART300

Бренд: Mackie Страницы: 6

Art Series ART200A

Бренд: Mackie Страницы: 2

Бренд: Rain Bird Страницы: 96

Bell & Gossett ecocirc XL Series

Бренд: Xylem Страницы: 62

Бренд: DAB Страницы: 228

Бренд: Medion Страницы: 122

Бренд: Sensitron Страницы: 11

Бренд: Clarion Страницы: 83

Бренд: Acces Страницы: 22

Бренд: AES global Страницы: 16

Бренд: Denver Страницы: 12

Бренд: VIA Technologies Страницы: 2

I/O System 750 Series

Бренд: WAGO Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды