Panasonic TC-PXXGT30 Скачать руководство пользователя страница 32

Страница: 32 / 83

Power LED Error Code Definition (1 of 2)

LIST OF BOARDS POSSIBLY CASUSING THE FAILURE

POWER LED

ERROR

CODE

CIRCUIT MONITORED

CONDITIONS TRIGGERING

THE SHUTDOWN

MOST

COMMON

OCCASIONALLY

RARELY

NO BLINLK
SOLID RED

LSI Error

Shorted Vsus
Shorted Vda
Shorted P15V

SC - SS

Panel

1 BLINLK

Panel Information SOS

PD5 Start-up SOS

Communication problem between the System CPU
(IC8001) and the Panel CPU (IC9003)

4 BLINKS

Power Supply output

voltages

Regulation issues with any of the voltages output from the

power supply.
Wrong diagnostic by the A board

P A

6 BLINKS

SC Energy Recovery Circuit

An increase or reduction of the Energy Recovery Circuit

output (MID).
Open connection of the P15V line between the P and A
board.

Open connection between any of the ribbon cables on the
C boards and the A board.
Open connection between the ribbon cable/cables

interconnecting the C boards.
Wrong diagnostic by the A board.

SC A

7 BLINKS

Scan Drive Circuit and

Connection between the SC

board and the SM(SU/SD)

board.

Missing Vsus.

Abnormality of the scan circuit output, the 15V_F, the
scn_pro, and Vscn circuit.

Loose or open Connection between the SC board and the
SM(SU/SD) board (SC41, SC42, SC46).
Open or loose connection between connectors SC2/P2

Wrong diagnostic by the A board
Defective Panel

SU-

SD/SS

Panel A

8 BLINKS

Sustain Drive Circuit and

Connection between the SS

board and the Panel.

Abnormality of the Sustain drive circuit.

Open or loose connection between the SS board and FPCs
from the panel (SS61, SS64, SS21, SS24, and SS58).
Open or loose connection between connectors C10/C20

Open or loose connection between A20 and SC20.
Wrong diagnostic by the A board

SS Panel A

Note:

When connector SC20/A20 is disconnected on the 2011 models, the TV shuts down with 8 blinks. When

this is done on the 2009 and 2010 models, the TV shuts down with 6 blinks.

Slide 32

Содержание TC-PXXGT30




















































































Результаты поиска

Содержание TC-PXXGT30

Отзывы:

Бренды по названию

Популярные бренды

Panasonic TC-PXXGT30, Техническое руководство

Результаты поиска

Содержание TC-PXXGT30

Отзывы:

Бренды по названию

Популярные бренды