7
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PROD-
UCT DAMAGE, DO NOT EXPOSE THIS APPLIANCE TO RAIN,
SPLASHING, DRIPPING OR MOISTURE.
CAUTION!
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
CAUTION:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful inter-
ference in a residential installation. This equipment generates, uses and can ra-
diate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the follow-
ing measures:
≥
Reorient or relocate the receiving antenna.
≥
Increase the separation between the equipment and receiver.
≥
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
≥
Consult the dealer or an experienced radio/TV technician for help.
Any unauthorized changes or modifications to this equipment would void the
user’s authority to operate this device.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
THE FOLLOWING APPLIES ONLY IN THE U.S.A.
Listening to the Radio
The letters such as
J
in the various illustrations refer to the descriptions in the “Location of Controls” section. (See page 4.)
When using overseas
(main unit only)
Change the frequency step according to the area.
Preparation:
Press [RADIO/BAND] to switch on the power.
1
Press for more than 5 seconds to display the step.
2
Within 10 seconds
Press to select the step.
FM U0.2
(original setting)
:
FM 0.2 MHz, AM 10 kHz
FM U0.1 :
FM 0.1 MHz, AM 10 kHz
E :
FM 0.05 MHz, AM 9 kHz
3
Within 10 seconds
Press and hold until the frequency is displayed to con-
firm the step.
∫
To return to the previous frequency step
Repeat the above procedure.
Note
!
Converting the allocation erases the stations previously stored in memory.
Changing the sound quality
The operation is the same as when playing CDs.
(See page 4.)
To obtain good reception
AM
Try various directions to obtain optimum reception.
Note
!
The AM antenna is located in the lid of the unit so noise may increase if the unit is
held. This is not malfunction.
FM
The headphone/earphone cord is also the FM antenna, so extend it rather than leav-
ing it coiled.
∫
How to receive an FM broadcast clearly
Press for more than 1.5 seconds during FM reception.
(main unit only)
Leave off under normal conditions. Set to “CITY” if reception is poor or if there is in-
terference from another station.
To select stereo or monaural FM
Press during FM reception.
(main unit only)
∫
When there is noise during FM reception
Select
“MONO”.
Sound becomes monaural, but noise is reduced.
J
FM RECEPT
CITY/NOR
MODE
“
CITY
”
(----.
“ ” (normal)
“
MONO
”
(----.
“ ” (stereo)
C
S-XBS
AUTO
MEMORY
FM
AM
VOL
MONO
CITY
SORRY
1
M
L
FM MODE
MONO/ST
C
S-XBS
AUTO
MEMORY
FM
AM
VOL
MONO
CITY
TUNED
SORRY
1
M
G
RADIO/
BAND
B
C
MEMORY/
RECALL
Each time the button is pressed;
C
S-XBS
AUTO
MEMORY
FM
AM
VOL
MONO
CITY
TUNED
SORRY
1
M
Each time the button is pressed;
Each time the button is pressed;
FM U0.2
,#
FM U0.1
,#
E
^------------------------------------------J
The product you have purchased is powered by a nickel-cadmium
battery which is recyclable. Please call 1-800-8-BATTERY for infor-
mation on how to recycle this battery.
Ni-Cd
RBRC
RBRC
Product Service
Do not attempt to remove the cover(s) or repair the unit yourself. Refer servicing to
qualified personnel only.
Product information
For product service, product information or assistance with product operation:
In the U.S.A., contact the Panasonic Customer Call Center at 1-800-211-7262,
or e-mail [email protected], or web site (http://www.
panasonic.com).
In Canada, contact Panasonic Canada Inc. Customer Care Centre at 905-624-5505,
web site (www.panasonic.ca), or an authorized Servicentre closest to you.
User memo:
DATE OF PURCHASE
DEALER NAME
DEALER ADDRESS
TELEPHONE NUMBER
