RQ
TX00
19
37
T
roub
le
sh
oo
tin
g g
ui
de
Troubleshooting guide
Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the
solutions indicated in the chart do not solve the problem, consult your dealer for instructions.
(Continued on next page)
Power
No power.
≥
Insert the AC mains lead securely.
7
The unit is automatically
switched to standby
mode.
≥
The Sleep timer was working and had reached the set time limit.
10
Unit displays
The display is dark.
≥
Select “Bright” in “FL Dimmer” in the “Others” menu.
27
“NO PLAY”
≥
You inserted a disc the unit cannot play; insert one it can.
≥
You inserted a blank disc.
≥
You inserted a disc that has not been finalized.
12
—
—
“NO DISC”
≥
You have not inserted a disc; insert one.
≥
You have not inserted the disc correctly; insert it correctly.
—
14
“OVER CURRENT
ERROR”
≥
The USB device is drawing too much power. Switch to DVD/CD mode,
remove the USB and turn the unit off.
—
“F61”
≥
Check and correct the speaker cable connections.
If this does not fix the problem, consult the dealer.
6
“F76”
≥
There is a power supply problem. Consult the dealer.
—
“DVD U11”
≥
Disc may be dirty. Wipe it clean.
43
“ERROR”
≥
Incorrect operation performed. Read the instructions and try again.
—
“DVD H
∑∑
”
“DVD F
∑∑∑
”
∑
stands for a number.
≥
Trouble may have occurred. The numbers following “H” and “F” depend on
the status of the unit. Turn the unit off and then back on. Alternatively, turn
the unit off, disconnect the AC mains lead, and then reconnect it.
≥
If the service numbers fail to clear, note the service number and contact a
qualified service person.
—
—
“D.MIX” is flashing.
[DVD-A]
≥
Down-mixing is the process of remixing the 5.1 channel sound found on
some discs into two channels. The disc contains single-channel or 5.1
channel signals which may not be reproduced authentically.
—
“U70
∑
”
∑
stands for a number.
The actual number following
“U70” will depend on the
state of this unit.
≥
The HDMI connection acts unusually.
– The connected equipment is not HDMI-compatible.
– Please use HDMI cables that have the HDMI logo (as shown on the cover).
– The HDMI cable is too long.
– The HDMI cable is damaged.
—
—
—
—
“REMOTE 1” or
“REMOTE 2”
≥
Match the modes on this unit and remote control. Depending on the number
being displayed (“1” or “2”), press and hold [ENTER] and the corresponding
numbered button ([1] or [2]) for at least 2 seconds.
10
General operation
No response when any
buttons are pressed.
≥
This unit cannot play discs other than the ones listed in these operating
instructions.
≥
The unit may not be operating properly due to lightning, static electricity or
some other external factor. Turn the unit off and then back on. Alternatively,
turn the unit off, disconnect the AC mains lead, and then reconnect it.
≥
Condensation has formed. Wait 1 to 2 hours for it to evaporate.
12
—
—
No response when remote
control buttons are
pressed.
≥
Check that the batteries are installed correctly.
≥
The batteries are depleted. Replace them with new ones.
≥
Aim the remote control at the remote control signal sensor and operate.
8
8
11
Other products respond to
the remote control.
≥
Change the remote control operating mode.
10
0019EB_p28-44.fm Page 37 Tuesday, April 17, 2007 8:29 PM
