RQTX1138
RQTX1138
RQTX1138
RQTX1138
13
ENGLISH
Maintenance
g
Pull out the power plug from the outlet for maintenance
beforehand and then wipe it using a soft and dried cloth.
When dirt is heavy, wring the cloth moistened in water tightly to wipe
the dirt, and then wipe it with a dried cloth.
Do not use solvents such as benzine, thinner, alcohol and detergent,
which may deform the coating of the outer case.
When using a chemical cloth, follow the precautions.
•
•
•
g
Care on the CD lens
Clean the lens regularly to prevent malfunctions. Use a blower to
remove dust and a cotton swab if it is extremely dirty.
Do not use the lens cleaner of the CD type.
•
•
13
Troubleshooting guide
(continued)
“F61” or “F76”
There is a power supply problem. Consult
the dealer.
“AUTO OFF”
The unit has been left unused for about
29 minutes and will shut down in a minute.
Press any button to cancel it.
“ILLEGAL OPEN”
Sliding door is not in correct position. Turn
the unit off and on again.
“NODEVICE”
The iPod/iPhone device is not inserted
correctly. Read the instructions and try
again (
➡
page 11).
“REMOTE 1”
The main unit is in “REMOTE 1” mode.
Switch the remote control to “REMOTE 1”
mode (
➡
page 12).
•
•
•
•
•
“REMOTE 2”
The main unit is in “REMOTE 2” mode.
Switch the remote control to “REMOTE 2”
mode (
➡
page 12).
“DIMMER”
Appears 10 seconds after the volume is
turned to “0”.
g
iPod/iPhone
iPod/iPhone does not turn on
Verify that the iPod/iPhone battery is not
depleted before connecting it to the unit.
Before inserting the iPod/iPhone into the
dock, turn both the unit and the iPod/iPhone
off. Turn the power on and select the
appropriate source.
No sound is heard from the speakers
The iPod/iPhone is not inserted correctly
into the dock. Turn the iPod/iPhone off and
remove it from the dock connector. Reinsert
it and turn it on again.
•
•
•
•
•
Make sure that the iPod/iPhone is actually
playing something.
Adjust the volume.
Distorted sound or the sound level is too
low
Make sure the equalizer function of the
iPod/iPhone is turned off.
iPod/iPhone cannot be controled by the
remote control or main unit
Make sure the iPod/iPhone is inserted
properly into the dock.
Check the dock connection and make sure
that iPod/iPhone is selected as the source
of music (
➡
page 11).
iPod/iPhone does not charge
Check all connections (
➡
page 4, 11).
•
•
•
•
•
•
Specifications
g
AMPLIFIER SECTION
RMS Output Power
Front Ch (both ch driven)
20 W per channel (6
Ω
), 1 kHz, 10 % THD
Total RMS power
40 W
FTC Output Power Stereo mode
Front Ch (both ch driven)
15 W per channel (6
Ω
), 20 Hz to 20 kHz, 10 % THD
Total FTC Stereo mode power
30 W
Phone jack
Terminal
Stereo, 3.5 mm (1/8") jack
Output level (CD, 1 kHz, -20 dB)
max. 0.2 mW + 0.2 mW, 32
Ω
Aux (Rear)
Terminal
Stereo, 3.5 mm (1/8") jack
g
TUNER SECTION
Preset Memory
FM 30 stations
AM 15 stations
Frequency Modulation (FM)
Frequency range
87.9 MHz to 107.9 MHz (200 kHz step)
87.5 MHz to 108.0 MHz (100 kHz step)
Antenna terminals
75
Ω
(unbalanced)
Amplitude Modulation (AM)
Frequency range
520 kHz to 1710 kHz (10 kHz step)
g
DISC SECTION
Disc played [8 cm (3") or 12 cm (5")]
(1) CD-Audio (CD-DA)
(2) CD-R/RW (CD-DA, MP3)
(3) MP3*
* MPEG-1 Layer 3, MPEG-2 Layer 3
Pick up
Wavelength
795 nm
Laser power
CLASS 1
Audio Output (Disc)
Number of channels
FL, FR, 2 channel
g
SPEAKER SECTION
Type
1 way, 1 speaker system (Passive Radiator)
Speaker unit(s)
Full range
6.5 cm (2
1
/
2
") Cone type x 1 / channel
Passive Radiator
8 cm (3") x 2 / channel
Impedance
6
Ω
g
GENERAL
Power supply
AC 120 V, 60 Hz
Power consumption
29 W
Dimensions (W x H x D)
500 mm x 201 mm x 102 mm
(19
11
/
16
" x 7
29
/
32
" x 4
1
/
32
")
(D = 69 mm (2
3
/
4
") minimum)
Mass (Weight)
Approx. 2.8 k
g
(6.2 lb.)
Operating temperature range
0 °C to +40 °C
(+32 °F to +104 °F)
Operating humidity range
35 % to 80 % RH (no condensation)
Power consumption in standby mode:
0.05 W (approx.)
Specifications are subject to change without notice.
Total harmonic distortion is measured by the digital spectrum
analyzer.
•
•
When the following situations occur, reset the memory:
There is no response when buttons are pressed.
You want to clear and reset the memory contents.
To reset memory
Disconnect the AC power supply cord.
(Wait for at least 3 minutes
before proceeding to step 2.)
•
•
While pressing and holding down [
8
, POWER] on the main unit,
reconnect the AC power supply cord.
“--------” appears on the display.
Release [
8
, POWER].
All the settings are returned to the factory preset. You will need to
reset the memory items.
Memory reset (Initialization)
