E
N
G
L
IS
H
ENGLISH
RQT9539
14
14
Specifications
Amplifier section
RMS output power stereo mode
Front Ch (both ch driven)
20 W per channel (6 ), 1 kHz, 10% THD
Total RMS stereo mode power
40 W
FTC output power stereo mode
Front Ch (both ch driven)
15 W per channel (6 ), 60 Hz to 20 kHz, 10% THD
Total FTC stereo mode power
30 W
FM/AM tuner, terminals section
Preset station
FM 30 stations
AM 15 stations
Frequency modulation (FM)
Frequency
range
87.9 MHz to 107.9 MHz (200 kHz step)
87.5 MHz to 108.0 MHz (100 kHz step)
Antenna
terminals
75 (unbalanced)
Amplitude modulation (AM)
Frequency
range
520 kHz to 1710 kHz (10 kHz step)
522 kHz to 1629 kHz (9 kHz step)
Headphones jack
Terminal
Stereo, 3.5 mm (
1
/
8
″
) jack
Disc section
Disc played [8 cm (3
″
) or 12 cm (5
″
)]
CD, CD-R/RW (CD-DA, MP3 formatted disc)
MPEG-1 Layer 3, MPEG-2 Layer 3
Pick up
Wavelength
790 nm (CD)
Laser power
CLASS 1 (CD)
Audio output (Disc)
Number of channels
2 ch (FL, FR)
FL = Front left channel
FR = Front right channel
USB section
USB port
USB standard
USB 2.0 full speed
Media file format support
MP3 ( .mp3)
USB device file system
FAT 12, FAT 16, FAT 32
USB port power
500 mA (max)
Speaker section
Type
2 way, 2 speaker system (bass reflex)
Speaker unit(s)
Woofer
10 cm (4
″
) cone type
Tweeter
6 cm (2
3
/
8
″
) cone type
Impedance
6
Output sound pressure
80.5 dB/W (1 m)
Frequency range
52 Hz to 31 kHz (–16 dB)
74 Hz to 27 kHz (–10 dB)
Dimensions (W x H x D)
145 mm x 224 mm x 197 mm
(5
23
/
32
″
x 8
13
/
16
″
x 7
3
/
4
″
)
Mass
1.9
k
g
(4.2 lbs)
General
Power supply
AC 120 V, 60 Hz
Power consumption
19
W
Dimensions (W x H x D)
153 mm x 224 mm x 232 mm
(6
1
/
32
″
x 8
13
/
16
″
x 9
1
/
8
″
)
Mass
1.7
k
g
(3.7 lbs)
Operating temperature range
0°C to +40°C
(+32°F to +104°F)
Operating humidity range
35% to 80% RH (no condensation)
Power consumption in standby mode
0.2 W (approximate)
Note:
1) Specifications are subject to change without notice.
Mass and dimensions are approximate.
2) Total harmonic distortion is measured by the digital
spectrum analyzer.
Maintenance
To clean this system, wipe with a soft, dry cloth.
• Never use alcohol, paint thinner or benzine to clean this
system.
• Before using chemically treated cloth, read the
instructions that came with the cloth carefully.
Memory reset (Initialization)
When the following situations occur, refer to the
instructions below to reset the memory:
• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.
To reset the memory
1
Disconnect the AC power supply cord.
(Wait 3 minutes before you continue with step 2.)
2
While you press and hold [
1
, POWER] on the
main unit, connect the AC power supply cord
again.
“– – – – – – – –” shows on the display panel.
3
Release [
1
, POWER].
All the settings are set back to the factory preset.
It is necessary to set the memory items again.
PM500_PC1_1us.indd 14
PM500_PC1_1us.indd 14
7/14/2011 12:13:04 PM
7/14/2011 12:13:04 PM
