34
RQT7061
R
A
DI
O &
S
OUND
The radio
Preparation
≥
Switch [HOME THEATER, TV] to “HOME THEATER”.
≥
Press [FM/AM] to select “FM” or “AM” as the source.
1
Press [
X
TUNING] or [TUNING
W
] to
select the frequency of the required
station.
Remote control: Press [
6
] or [
5
].
TUNED: Displayed when a radio station is
tuned.
ST:
Displayed when a stereo FM
broadcast is being received.
Press and hold [
X
TUNING] or [TUNING
W
] ([
6
] or [
5
]
on the remote control) until the frequency starts scrolling to
start automatic tuning. Tuning stops when a station is found.
2
Adjust the volume.
[Main\unit\only]
∫
If noise is excessive
Press [FM MODE].
Each time you press the button:
FM: Changes between stereo and forced monaural.
AM: BP1
()
BP2 (BP
l
Beat Proof)
Select either BP1 or BP2, whichever receives better reception.
The FM mode is canceled when you change the frequency.
∫
FM frequency step
The step is factory-set to 0.2 MHz, but you can change it to receive
broadcasts allocated 0.1-MHz steps.
1 Press [FM/AM] to select “FM”.
2 Press and hold [FM/AM].
After a few seconds the display changes to show the current
minimum frequency. Continue to hold the button down. The
minimum frequency changes and the step is changed.
To return to the original step, repeat the above steps.
[Note]
Any FM and AM frequencies preset in channels will be initialized by
this procedure. Preset them again.
Preset channels to make selection simple.
Up to 12 stations can each be set in the FM and AM bands.
[Main\unit\only]
1
Tune to “FM 87.9” MHz or “FM
87.5” MHz (
➡
left).
2
Press and hold [MEMORY].
Release the button when “AUTO” is displayed.
The tuner presets all the stations it can receive into the
channels in ascending order.
“SET OK” is displayed when the stations are set. The last
station to be set is then played.
3
Tune to “AM 520” kHz.
Repeat step 2 for AM automatic presetting.
“ERROR” is displayed
Presetting was unsuccessful. Preset manually.
[Main\unit\only]
1
Tune to the station (
➡
left).
2
Press [MEMORY].
3
While “MEMO” is flashing
Press [
X
,
W
CHANNEL] to select a
channel and press [MEMORY].
The station occupying a channel is erased if another station is preset
in that channel.
1
Press [FM/AM] to select “FM” or
“AM”.
2
Press the numbered buttons or
[
W
X
CH] to select the channel.
e.g., “2”:
[0]
➡
[2]
“12”:
[1]
➡
[2]
[Note]
If there is nearby electrical interference during auto tuning the
frequency may come to a halt without locating a channel. Turn off the
power of the nearby electrical equipment.
Manual tuning
CH
VOLUME
SKIP
STOP
PAUSE
PLAY/x1.3
SLOW/SEARCH
CANCEL
1
2
3
4
5
6
7
8
9
0
100
HOME THEATER
TV
CH SELECT
RETURN
L1/OPT
FUNCTIONS
TOP MENU
ENTER
DIRECT NAVIGATOR
MENU
PLAY LIST
MIX
2CH
TEST
FM/AM
TV/VIDEO
INPUT SELECT
OPEN/CLOSE
DISPLAY
DVD
VCR Plus+
POWER
POWER
PRO LOGIC
6
,
5
HOME
THEATER,TV
W
X
CH
r
s
VOLUME
FM/AM
DOWN
TIME SLIP
REC
ERASE
MEMORY
FM/AM
DVD
REC MODE
FM MODE
UP
VOLUME
OPEN/CLOSE
TUNING
TIME SLIP
CHANNEL
PHONES
X
,
W
CHANNEL
FM/AM
MEMORY
FM MODE
VOLUME DOWN, UP
X
TUNING
W
Numbered
buttons
ST
TUNED
FM
Preset tuning
Automatic presetting
Manual presetting
Selecting channels
CH
ST MEMO
TUNED
FM
CH
ST
TUNED
FM
7061en.book 34 ページ ２００３年７月１日 火曜日 午前１１時４４分
