4
VQT2Z56
Safety precautions
Set the unit up on an even surface away from direct sunlight,
high temperatures, high humidity, and excessive vibration.
These conditions can damage the cabinet and other
components, thereby shortening the unit’s service life. Do not
place heavy items on the unit.
Do not use high voltage power sources. This can overload the
unit and cause a fire. Do not use a DC power source. Check
the source carefully when setting the unit up on a ship or other
place where DC is used.
Ensure the AC mains lead is connected correctly and not
damaged. Poor connection and lead damage can cause fire or
electric shock. Do not pull, bend, or place heavy items on the
lead.
Grasp the plug firmly when unplugging the lead. Pulling the AC
mains lead can cause electric shock. Do not handle the plug
with wet hands. This can cause electric shock.
Do not let metal objects fall inside the unit. This can cause
electric shock or malfunction.
Do not let liquids get into the unit. This can cause electric
shock or malfunction. If this occurs, immediately disconnect
the unit from the power supply and contact your dealer.
Do not spray insecticides onto or into the unit. They contain
flammable gases which can ignite if sprayed into the unit.
Do not attempt to repair this unit by yourself. If sound is
interrupted, indicators fail to light, smoke appears, or any other
problem that is not covered in these instructions occurs,
disconnect the AC mains lead and contact your dealer or an
authorized service centre. Electric shock or damage to the unit
can occur if the unit is repaired, disassembled or reconstructed
by unqualified persons.
Extend operating life by disconnecting the unit from the power
source if it is not to be used for a long time.
Requests regarding handling:
≥
Exercise care when selecting the location for the unit because it may
discolour or deform due to light or heat if it is placed where it is exposed to
direct sunlight, or near a heater.
≥
Clean the wall mount brackets by wiping them with a soft, dry cloth (such
as cotton or flannel). If the wall mount brackets are very dirty, remove the
dirt using a neutral detergent diluted in water, and then wipe them clean
with a dry cloth.
Do not use benzine, thinner, or furniture wax as this may cause the coating
to peel.
Precautions for wall mount bracket installation
≥
The wall mount brackets are for use in attaching the unit to a vertical wall.
Do not attach to any surface other than a vertical wall.
≥
To ensure correct unit performance and prevent trouble, do not install at
any of the following locations:
– Near sprinklers or fire/smoke detectors
– Where there is a risk of exposure to vibration or impact
– Near high-voltage wires or dynamic power supplies
– Near sources of magnetism, heat, water vapour or soot
– Locations exposed to air blown from heating equipment
– Where droplets of condensation from an air conditioner or other unit may
form.
≥
Attach using techniques suited to the structure and materials of the
installation location.
≥
Spread a soft blanket or cloth over the floor so that the unit and floor will not
be marked or scratched during the assembly and installation work.
≥
When screwing down the parts, ensure that the screws are neither
insufficiently tightened nor over tightened.
≥
Take sufficient care to ensure safety around you when performing the
assembly and installation work or while moving about during the course of
the work.
≥
Do not install the unit underneath ceiling lamps (spotlights, halogen lamps,
etc.). Otherwise, the cabinet may be bent or damaged by high heat.
Do not connect this unit to the household mains socket while installing.
When screwing down the parts, ensure that the screws are not
insufficiently tightened or over tightened.
WARNING
Ensure that the installation location is strong enough to support
long-term use.
≥
If its strength becomes insufficient over the course of long-term use, the
unit may drop, possibly causing injury.
The installation work should never be done by any other than a qualified
installation specialist.
≥
Incorrect installation may cause equipment to fall, and personal injury may
result.
Include a safety factor when considering the strength of the proposed
installation location (approx. 10 times the product weight).
≥
If strength is not sufficient the equipment may fall, and personal injury may
result.
Do not install at a location that cannot bear the load.
≥
If the installation location lacks sufficient strength, the equipment may fall.
Do not modify the wall mount brackets.
≥
Otherwise the unit may fall and become damaged, and personal injury may
result.
Install the unit by taking only the steps which are specified in these
instructions: Do not install it in any other way.
≥
Otherwise the unit may drop and become damaged, and personal injury
may result.
Do not install at a location other than a vertical wall.
≥
Otherwise the unit may drop and become damaged, and personal injury
may result.
CAUTION
Do not install at any locations subject to humidity, dust, smoke, steam
or heat or under an air conditioner where water may drip onto the unit.
≥
This may have an adverse effect on the unit and cause fire or electric shock.
Leave a clearance between the rear panel and the wall.
≥
The unit has air ventilation holes at the front and rear. Covering these may
result in a fire.
Install the mounting screws and power cable in such a way that they will
not make contact with metal objects or wiring inside the wall.
≥
Electric shocks may result from contact with any metal objects inside the wall.
For installation, use the special-purpose constituent parts.
≥
Otherwise, the unit may fall off the wall, and personal injury may result.
When removing this unit, remove the wall mounting screws as well.
≥
Otherwise the mounting screws may get caught and personal injury may
result.
To operate this unit safely, install it at an appropriate height.
≥
Otherwise the unit may fall, and personal injury may result.
Placement
Voltage
AC mains lead protection
Foreign matter
Service
WARNING:
PROFESSIONAL INSTALLATION IS REQUIRED.
PANASONIC DISCLAIMS ANY PROPERTY DAMAGE AND/OR
SERIOUS INJURY, INCLUDING DEATH RESULTING FROM IMPROPER
INSTALLATION OR INCORRECT HANDLING.
SCBFT800_VQT2Z56_eng.book 4 ページ ２０１０年８月４日 水曜日 午後５時１０分
