Panasonic SC-BFT800, Руководство по эксплуатации, Страница: 20 / 52

20
VQT2Z56
≥
If you can not find the SSID*
2
, select “Search again”.
2
Press [RETURN] and then press [OK].
Then select an item on the following screen which
corresponds to the authentication type noted down in step
1
(
>
19).
Follow the on-screen instructions to make the settings.
≥
Input your encryption key code in “Encryption Key”
supplied with your Wireless router (Access point).
*1 Wi-Fi Protected Setup-compatible Wireless router (Access point) may
have the mark.
*2 An SSID (Service Set IDentification) is a name used by wireless LAN to
identify a particular network. Transmission is possible if the SSID
matches for both devices.
Access Point Connection Setting
Network Easy Setting (Connection Test)
Network Easy Setting (Internet Connection Test)
When you experience
problems with settings
Display Check the following
A conflict with other
devices occurred.
≥
Please wait a few moments,
and then try again.
A time out error occurred.
≥ Setting of the Wireless
router (Access point) for
MAC Address etc.
≥ The signal may be weak.
Using the USB extension
cable supplied with the
Wireless LAN Adaptor,
adjust the position of the
Wireless LAN Adaptor.
≥
The SSID and the
encryption key of the
Wireless router (Access
point).
≥
Please wait a few moments,
and then try again.
An authentication error or a
time out error occurred.
A device error occurred.
≥
Connection of Wireless LAN
Adaptor
If there is no improvement in
symptom, consult your
dealer.
Access Point Connection Setting
WPA2-PSK (AES/TKIP)
WPA-PSK (AES/TKIP)
Open/Shared Key (WEP)
Open system
Select authentication type.
OK
Access Point Connection Setting
Yes No
Failed to connect to the access point.
A conflict with other devices occurred.
Do you wish to setup Access Point
Connection Setting again ?
Display
Check the
following
1. LAN cable connection or
Connection to access point
:Fail
≥
Connection of
the LAN
cables (
>
17)
2. IP address setting :Fail
3. Connection to gateway :Fail
1. LAN cable connection or
Connection to access point
:Pass
≥ Connection
and settings
of the hub
and router
≥
Settings of
“IP Address /
DNS
Settings”
(
> 41)
2. IP address setting :Fail
3. Connection to gateway :Fail
1. LAN cable connection or
Connection to access point
:Pass
2. IP address setting
:Home
network
available
3. Connection to gateway :Fail
1. LAN cable connection or
Connection to access point
:Pass
2. IP address setting :Pass
3. Connection to gateway :Fail
Display Check the following
Cannot find the server.
(B019)
≥
“Primary DNS” and “Secondary
DNS” settings of “IP Address /
DNS Settings” (
> 41)
Failed to connect to
the server.
(B020)
≥ The server may be busy or the
service may have been
suspended. Please wait a few
moments, and then try again.
≥
Settings of “Proxy Server
Settings” (
> 41) and the router
OK
Network Easy Setting (Connection Test)
Yes No
Complete.
1. LAN cable connection
2. IP address setting
3. Connection to gateway
LAN cable is not connected.
Please check the connection.
Select “Yes” and press [OK] to check network
connection again.
Select “No” and press [OK] to finish Network
Easy Setting.
: Fail
: Fail
: Fail
OK
Network Easy Setting (Internet Connection Test)
Complete.
- Connection to the Internet : Fail(B019)
Failed the connection test.
Cannot find the server.(B019)
Please refer to the operating instructions for the cause
of the error and the countermeasure for it.
Press [OK].
SCBFT800_VQT2Z56_eng.book 20 ページ ２０１０年８月４日 水曜日 午後５時１０分