Panasonic PT-RZ870LBEJ, Руководство по эксплуатации

Страница: 104 / 212

Chapter 4 Settings — [DISPLAY OPTION] menu
104 - ENGLISH
Note
f
Backup function is enabled only when the [BACKUP INPUT MODE] is set to [ON], and the same signal is input to the <DVI-D IN> and
<HDMI IN> terminals.
f
To switch to the backup input signal using the backup function, make sure that the following three conditions are satisfied to be ready to use
the function.
g
Set [BACKUP INPUT MODE] to [ON].
g
Input the same signal to the primary and secondary inputs.
g
Display the image of the primary input.
f
If the input is switched to other than the primary or secondary input while the backup function is ready for use, the state of readiness to use
the backup function is canceled. To switch to the backup input signal using the backup function again, switch to the primary input.
f
[BACKUP INPUT STATUS] is displayed in the input guide (
x
page 110) and [STATUS] screen (
x
pages 74, 138) when [BACKUP
INPUT MODE] is set to [ON].
When switching to the backup input signal is possible using the backup function, [ACTIVE] is displayed in [BACKUP INPUT STATUS]. When
it is not possible, [INACTIVE] is displayed instead.
The secondary input will be the backup input when [BACKUP INPUT STATUS] is displaying [ACTIVE] while the image from the primary
input is displayed.
The primary input will be the backup input when [BACKUP INPUT STATUS] is displaying [ACTIVE] while the image from the secondary
input is displayed.
f
The input is switched seamlessly when the DVI-D and HDMI inputs are switched while [BACKUP INPUT MODE] is set to [ON] and switching
to the backup input signal is possible.
f
When [AUTOMATIC SWITCHING] is set to [ENABLE], and [BACKUP INPUT STATUS] is [ACTIVE], the signal is switched to the backup
input if a disruption occurs in the input signal.
f
When [AUTOMATIC SWITCHING] is set to [ENABLE] and the signal is automatically switched to the backup input due to disruption of the
input signal, [BACKUP INPUT STATUS] changes to [INACTIVE]. In this case, switching to the backup input signal is not possible until the
original input signal is restored. If the signal is automatically switched to the backup input, switching to the backup input signal becomes
possible when the original input signal is restored. In this case, the current input is retained.
f
[BACKUP INPUT SETTING] cannot be set during P IN P. The backup operation is not performed either.
[RGB IN]
Set the <RGB 1 IN> terminal and the <RGB 2 IN> terminal.
Setting [RGB1 INPUT SETTING]
1) Press
as
to select [RGB IN].
2) Press the <ENTER> button.
f
The [RGB IN] screen is displayed.
3) Press
as
to select [RGB1 INPUT SETTING].
4) Press
qw
to switch the item.
f
The items will switch each time you press the button.
[RGB/YP
B
P
R
] Select this item when an RGB signal or YC
B
C
R
/YP
B
P
R
signal is input to the <RGB 1 IN> terminal.
[VIDEO] Select this item when a video signal is input to the <RGB 1 IN> terminal (<R/P
R
/VIDEO>).
[Y/C]
Select this item when a luminance signal and color signal are input to the <RGB 1 IN> terminal (<G/
Y>, <B/P
B
/C>).
Switching the slice level of an input synchronization signal
1) Press
as
to select [RGB IN].
2) Press the <ENTER> button.
f
The [RGB IN] screen is displayed.
3) Press
as
to select [RGB1 SYNC SLICE LEVEL] or [RGB2 SYNC SLICE LEVEL].
4) Press
qw
to switch the item.
[LOW] Set the slice level to [LOW].
[HIGH] Set the slice level to [HIGH].
Setting [RGB2 EDID MODE]
1) Press
as
to select [RGB IN].