Others
116
LSQT1123
Before requesting repair
(Problems and solutions)
Power/Body
1: The movie camera power cannot be turned
on.
• Is the battery fully charged? Use a fully
charged battery.
• The battery protection circuit may have
operated. Attach the battery to the AC adaptor
for 5 to 10 seconds. If the movie camera still
cannot be used, the battery is faulty.
• Is the LCD monitor open or the viewfinder
extend?
2: The movie camera power is turned off
automatically.
• If you set [POWER SAVE] to [5 MINUTES] and
do not operate the movie camera for about
5 continuous minutes, the power is
automatically turned off for tape protection and
power conservation. To resume recording, turn
the [OFF/ON] switch to [OFF]. Then turn it to
[ON] again. (
-112-
) Also, if you set
[POWER SAVE] to [OFF], the power does not
automatically turn off.
3: The movie camera power does not stay on
long enough.
• Is the battery low? If the remaining battery
power indication is flashing or the message
“LOW BATTERY” is displayed, the battery has
run down. Charge the battery or attach a fully
charged battery. (
-71-
)
• Has condensation occurred? When you carry
the movie camera from a cold place into a
warm place, condensation may occur inside it.
If so, the power is turned off automatically,
disabling all operations except for taking
cassettes out. Wait until the condensation
indication disappears. (
-120-
)
4: Battery runs down quickly.
• Is the battery fully charged? Charge it with the
AC adaptor. (
-71-
)
• Are you using the battery in an extremely cold
place? The battery is affected by ambient
temperature. In cold places, the operating time
of the battery becomes shorter.
• Has the battery worn out? The battery has a
limited life. If the operating time is still too short
even after the battery is fully charged,
depending on the usage, the battery has worn
out and can no longer be used.
5: The movie camera cannot be operated
though powered up.
The movie camera does not operate
normally.
• The movie camera cannot be operated unless
you open the LCD monitor or extend the
viewfinder.
• Remove the cassette and the card and then
press the [RESET] button. (
-119-
) If normal
conditions are not restored yet, turn off the
power. Then, about 1 minute later, turn on the
power again. (Conducting the above operation
when the access lamp is on may destroy the
data on the card.)
6: The cassette cannot be removed.
• Does the status indicator comes on when
opening the cassette cover? (
-76-
) Make sure
that the battery and the AC adaptor are
properly connected. (
-71-
)
• Is the battery in use discharged? Charge the
battery and remove the cassette.
• Close the cassette cover completely, and fully
open it again. (
-76-
)
7: No operation other than cassette removal
can be performed.
• Has condensation occurred? Wait until the
condensation indication disappears. (
-120-
)
8: The remote control does not function.
• Has the button-type battery of the remote
control run out? Replace it with a new
button-type battery. (
-83-
)
• Is the setting on the remote control correct? If
the setting on the remote control is not in
agreement with the [REMOTE] setting on the
movie camera, the remote control does not
operate. (
-83-
)
LSQT1123_ENG.book 116 ページ 2006年12月25日 月曜日 午前9時45分
Содержание NV-GS85GC
Страница 254: ...254 LSQT1123 LSQT1123HIN book 254 ページ 2006年12月27日 水曜日 午前10時4分 ...
Страница 255: ...255 LSQT1123 LSQT1123HIN book 255 ページ 2006年12月27日 水曜日 午前10時4分 ...
Страница 256: ...Matsushita Electric Industrial Co Ltd Web site http panasonic net LSQT1123HIN book 256 ページ 2006年12月27日 水曜日 午前10時4分 ...
Страница 384: ...Matsushita Electric Industrial Co Ltd Web Site http panasonic net 85_BackGC fm 128 ページ 2006年11月14日 火曜日 午前10時46分 ...