Panasonic NV-GS10, Руководство по эксплуатации

Страница: 37 / 52

Others
-37-
ª
To Change the Display Mode
By changing [DISPLAY] on the
[DISPLAY SETUP] Sub-Menu, you can change
the Display Mode to All Function Display [ALL],
Partial Display [PARTIAL] and Minimum Display
[OFF]. (
-14-
)
Owner ID
You can register your name and address in your
Movie Camera to identify the owner.
1
Set [CAMERA FUNCTIONS] >>
[OTHER FUNCTIONS1] >> [OWNER ID SET]
>> [YES].
≥
The [OWNER ID] Menu appears.
2
Turn the [PUSH] Dial (32) to select
[PIN NUMBER] and press the [PUSH] Dial
(32) to input desired numbers.
3
Turn the [PUSH] Dial (32) to select numbers
and press the [PUSH] Dial (32) to enter
them.
≥
Be sure to input 4 digits. Otherwise the Pin
Number will not be registered.
4
Press the [
∫
] Button.
5
Repeat Steps 2–4 to input desired
characters for [NAME] and [POSTCODE].
≥
You can input up to 12 characters in [NAME],
and up to 11 characters in [POSTCODE].
6
Press the [
∫
] Button to finish the setup.
To Verify Owner ID
Keep pressing the [
;
] Button for approximately
5 seconds.
To Correct the Contents
If Owner ID has already been set, carrying out
Step 1 will display [INPUT PIN NUMBER] on the
screen. Input the Pin Number you have already
selected. If the number is not correct, the screen
will not change. If the number is correct, the
contents of the setup will be displayed. (By
repeating Steps 2 to 4, you can change the
contents.)
Initializing the Modes
You can change the Menu settings back to the
shipping condition.
1
Set [CAMERA FUNCTIONS] >>
[OTHER FUNCTIONS2] >> [INITIAL SET] >>
[YES].
≥
The initializing takes for a while.
≥
After the initializing is completed, the
[COMPLETED] Indication appears with
beeps.
≥
Initializing will not erase the Owner ID setting
and the clock setting (
-15-
) that has been
adjusted.
Warning/Alarm Indications
If any one of the following indications lights up or
flashes, please check the condition of the Movie
Camera.
3
: Condensation has occurred.
-43-
Y
: The accidental erasure prevention slider on
the inserted Cassette is open (that is, set to
[SAVE]).
You are about to do audio dubbing on the
unrecorded (blank) portion of the tape.
No Cassette is inserted.
-12-
6
: The Battery is low. Recharge it.
-9-
0
: The built-in battery is low.
-16-
:
: The video heads are dirty.
-43-
2
END:
The tape came to end during recording.
REMOTE:
Wrong Remote Controller Mode has been
selected.
-9-
UNPLAYABLE TAPE
(OTHER FORMAT):
You are attempting to play back a tape
section that has been recorded with a
different TV system.
UNABLE TO A. DUB
(LP RECORDED):
Because the original recording was done in
LP Mode, audio dubbing cannot be
performed.
INCOMPATIBLE TAPE:
This Cassette is incompatible.
PLEASE RE-OPERATE
AFTER PUSHING
RESET BUTTON:
Mechanism Irregular is detected. Press the
[RESET] Button (
-7-
). This may solve the
problem.
TO SERVICE:
It is a malfunction.
COPY INHIBITED:
Because the medium is protected by a copy
guard, images cannot be recorded
correctly.
Notes and Hints
ª
Concerning the Power Supply
≥
When the Movie Camera is used for a long time,
the Camera body becomes warm, but this is not
a malfunction.
≥
If the [CHARGE] Lamp does not light up
although the Battery is attached to the AC
Adaptor, detach the Battery and reattach it.
ENGText.fm 37 ページ ２００３年２月２４日 月曜日 午後９時５８分