Panasonic NR-B32FX3 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 52

background image

40

11.7. Disassembly of Compressor

Room

11.7.1. Pan Water EVA., Motor Protector,

Cluster Block

1. Pan Water EVA

a. Pull Power Supply Cord out.
b. Remove the six screws on Cover Panel Compressor.

c. Pull and remove Cover Panel Compressor toward you

from upper side.

d. Pull Pan Water EVA. toward you while pressing it up.

NOTICE

• When you install Cover Panel Compressor, set the holes

of the six screws.

• Adjust its position, and tighten the six screws.

2. Motor Protector

a. Insert a screwdriver (-) into the gap between Protector

Cover and Compressor like the figure.
Pry off Protector Cover in a screwdriver (-).
Remove Protector Cover.

b. Take Motor Protector out from inside Protector Cover.

3. Cluster Block

a. Pull Cluster Block out from Compressor like the figure.

NOTICE

• Be careful not to twist when you pull Cluster Block out or

install.

«
...
38
39
40
41
42
...
»

Содержание NR-B32FX3





















































Отзывы:

Нет отзывов

Похожие инструкции для NR-B32FX3

Бренд: Ocean Страницы: 11

Бренд: C3 Custom Coolers Страницы: 2

Бренд: U-Line Страницы: 2

Бренд: U-Line Страницы: 2

Бренд: U-Line Страницы: 2

Бренд: U-Line Страницы: 21

Бренд: V-ZUG Страницы: 36

Бренд: Ariston Страницы: 12

Бренд: Sub-Zero Страницы: 44

Бренд: SEVERIN Страницы: 1

Бренд: UNITED Страницы: 8

Бренд: True Страницы: 2

Бренд: Jenn-Air Страницы: 68

Бренд: Smeg Страницы: 17

Бренд: Coolest Страницы: 28

Бренд: Hanseatic Страницы: 56

Avallon AWC243TSZLH

Бренд: Ferguson Enterprises Страницы: 21

Бренд: La Germania Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды